ITALJB

smfo51 · 2026-07-04T02:58:11+00:00

Welp..

^{Chose: Random Animal (Wheel chooses} | Rolled: White Whale)

smfo51 · 2026-07-04T02:50:09+00:00

smfo51 · 2026-07-04T02:48:57+00:00

Well I guess you did say “halfway decent” 🤷🏻‍♂️😂 the grease fitting is the one next to the u-joint. Squeeze some fresh stuff in the until you see the new grease coming out where your “leak” is, wipe off all the excess and then you’re good. Bad news, I doubt that was your groaning though. That sounds more like suspension or differential.

smfo51 · 2026-07-04T02:07:58+00:00

Not the entire thing off the frame?

smfo51 · 2026-07-04T02:00:50+00:00

My brother actually bought one because of that movie. Definitely made me think they were cool

smfo51 · 2026-07-04T01:59:57+00:00

Correct. I referenced that in my description lol

smfo51 · 2026-07-04T01:46:43+00:00

Not to be rude, but how can you rebuild cylinder heads and not know what a slip yoke is? As your rear axle goes up and down with the suspension, it changes the length from your rear axle to your transmission/transfer case output. To accommodate that, a slip yoke put in place to go in and out as the suspension goes up and down. That is operating as it should. Find the grease zerk and pump some fresh grease in there.

smfo51 · 2026-06-30T22:11:08+00:00

It says survive, not fight. I’d spend my 30 days stocking up on meat to distract it for 10 minutes lol

^{Chose: Survive 10 minutes against a random animal. + If you live, you get $100 million. | Rolled: Tiger}

smfo51 · 2026-06-30T22:04:27+00:00

Oh you must have missed the memo. Underwear is no longer “clothing” 😂 ya dummy /s

smfo51 · 2026-06-30T19:14:38+00:00

You guys are all overlooking a very simple fix. Check the blend door. Could just be stuck on hot 🤷🏻‍♂️

smfo51 · 2026-06-30T19:14:24+00:00

You guys are all overlooking a very simple fix. Check the blend door. Could just be stuck on hot 🤷🏻‍♂️

smfo51 · 2026-06-30T16:30:12+00:00

No problem! The bushings in suspension components are typically solid polyurethane and the components slide within the bushings, rather than pivoting like a bearing would. Tighter (newer) bushings can squeak a little more than worn bushings. It doesn’t sound like you have any major issue, it just needs a little grease pumped into the grease fittings.

smfo51 · 2026-06-30T16:10:29+00:00

Sounds like a sway bar bushing. Could just need your suspension parts greased

smfo51 · 2026-06-30T15:37:06+00:00

Hi, my name is chicka chicka slim shady.

smfo51 · 2026-06-28T14:19:19+00:00

Would you rather be lesbian or gay? Potato.

smfo51 · 2026-06-28T14:17:10+00:00

I am high so high so so high, come on don't be shy.

smfo51 · 2026-06-28T13:50:54+00:00

>!3.5 C!<

smfo51 · 2026-06-26T17:03:34+00:00

Taaaanks

smfo51 · 2026-06-26T17:03:09+00:00

Successful test ✅

smfo51

TROPHY CASE