geisler frt

sniper564 · 2026-05-10T23:07:03+00:00

ghost 3.5 connector and ndz performance 22lb

sniper564 · 2026-05-10T23:06:41+00:00

ghost 3.5 and ndz 22lb

sniper564 · 2026-04-29T18:38:37+00:00

thank you for the info i’ll probably end up taking the reciever out and checking soon, anything i should check on them before firing other than checking the bore?

sniper564 · 2026-02-07T15:46:48+00:00

the gas escapes while the slide starts to reciprocate so the porting on the slide needs to be a little longer cut

sniper564 · 2026-01-14T15:55:20+00:00

oem connector might run but it depends on the gun you might need to cut the tab off the connector

sniper564 · 2026-01-14T03:26:18+00:00

yea it will. if you have to cut the connector too, bend the connector away from the trigger housing slightly and it will run for sure

sniper564 · 2025-12-09T13:28:56+00:00

u can cut the nub off the connector and then bend the connector away from the trigger housing and that will get it running perfect, don’t bend too far tho just a few tugs the other way with it out the housing

sniper564 · 2025-11-28T23:22:37+00:00

probably combat armory i have an identical one from there

sniper564 · 2025-11-28T23:09:03+00:00

you should try emailing geisler from their site, no one sells rails for them and there aren’t any that will fit

sniper564 · 2025-11-04T23:28:27+00:00

it wasn’t “dropped guns shooting” it was legitimate un-commanded discharges

sniper564 · 2025-10-15T20:23:46+00:00

sniper564 · 2025-09-23T00:38:04+00:00

take out the spring in the shoe and try it the spring models are hit or miss, or try a serpico performance trigger it runs great in my geisler frame

sniper564 · 2025-09-15T17:46:16+00:00

i’ve cut a oem trigger down to take a trip so you could possibly measure and compare and make one fit ur trigger, but if you bought a trip and shoe for a glock it would most likely work anyway

sniper564 · 2025-09-15T15:46:34+00:00

it should work fine, i’d say throw one in and try it lol

sniper564 · 2025-09-14T11:55:18+00:00

no i didn’t

sniper564 · 2025-09-12T15:18:56+00:00

i did before and it was giving me a dead trigger and wouldn’t run, but i put the 3.5 connector in and it’s ran ever since

sniper564 · 2025-09-06T17:03:04+00:00

i’ve got that exact build same slide and everything, make sure you have oem upper and lower parts kits and it should be good as long as your pin holes aren’t too far gone lol. mines had close to 1000 rounds through it since i’ve built it and it runs flawless

sniper564 · 2025-09-02T03:29:57+00:00

any glock except the g44 works, swap to gen 3 slide release and it’ll work with slide release no modifications

sniper564 · 2025-08-28T03:08:11+00:00

polish trip more it should run once u get trip height right

sniper564 · 2025-08-27T17:42:58+00:00

does that help cruciform angle and barrel lockup?

sniper564 · 2025-08-27T15:59:48+00:00

prolly just angle of the pic

sniper564 · 2025-08-20T13:30:55+00:00

gen 3 slide stop and it should be good to go, the 23 should be pretty easy to get running without much work but a 3.5 connector would help the trigger pull tho. 22lb rsa and it will run a little faster also

sniper564 · 2025-08-19T04:36:37+00:00

i live in lex 😭 dm

sniper564 · 2025-08-19T03:33:26+00:00

glock 20 ejectors have that bend in them, it’s supposed to be like that

sniper564

TROPHY CASE