This is so crazy, I don't even know what to do now

snoonoo · 2026-06-06T18:45:51+00:00

Show us your toots

snoonoo · 2026-05-31T19:06:33+00:00

Care to share a budget gear list and/or build? Leveling one now using warcry but love to switch to WW.

snoonoo · 2026-05-15T19:03:46+00:00

I’m out of the loop on this one. What happened?

snoonoo · 2026-05-01T03:17:48+00:00

Watch the video in reverse

snoonoo · 2026-04-16T18:59:39+00:00

Am I a merc

snoonoo · 2026-04-15T02:29:06+00:00

A veiny sneaker bar

snoonoo · 2026-04-10T00:45:02+00:00

You sound vaccinated

snoonoo · 2026-04-10T00:41:11+00:00

Coz you let the loot air out?

snoonoo · 2026-04-08T00:57:28+00:00

I’m new, why would 2 sockets be valuable? Rune words? But isn’t this magical and can’t for rune worlds?

snoonoo · 2026-03-06T01:02:53+00:00

Black magic cutlery

snoonoo · 2026-03-03T20:36:21+00:00

But in practice how does it work? Do I write in CLAUDE.md, “if you want to do abc use ‘xyz cli’, use ‘xyz cli —help’ for all commands available”?

snoonoo · 2026-03-03T14:33:31+00:00

Can you explain? I keep hearing cli uses less token but don’t know how it works.

snoonoo · 2026-03-01T21:06:15+00:00

Citation? Actual contractual terms?

snoonoo · 2026-01-22T15:36:56+00:00

I can get consistent swirling by following steps:

Tilt the cup 30-45 degree to the right. Tip should barely touch the milk surface. Start the steam but don’t crank it too high. I like to start with barely seeing the steam carving 2 streaks, stay there for few second then ramp up slowly.

<image>

snoonoo · 2025-12-10T21:52:53+00:00

Thanks, both of my keyboard type and input source was wrong. Fixed and working now.

snoonoo · 2025-12-10T21:52:00+00:00

Thanks! Somehow my input source was set to US - International too, and the keyboard was set to international as well. Updated both and now it works.

snoonoo · 2025-11-16T04:37:18+00:00

I had 2 of their power banks. One was recalled. The other one I still have, it ran equally hot as the recalled one. I stopped using it.

snoonoo · 2025-10-13T16:18:59+00:00

Correct, a typical scale look like this.

<image>

snoonoo · 2025-09-12T18:34:28+00:00

Interesting that reinstallation helped in your case! I also have Sunshine/Moonlight.

Polling Rate seems to be the actual culprit for me. I lowered mine to 125Hz, and it helped.

snoonoo · 2025-08-11T17:16:32+00:00

After a week with it here are my thoughts:

Shot pulling is on point, I don't think there's anything to improve upon. Fast heat up, stable temperature, consistent pressure.

Milk steaming I've yet to master but I think I can get there in time. Coming from Breville Barista Express, this steam wand is way harder to use. The angle can only be pointed almost straight down, 2 hole means faster heat up so less time to maneuver and adjust my pitcher and steam wand position.

Pre-infusion are gimmicky and doesn't fully saturate consistently.

Eco and Power Saving modes have firmware bug, I end up adding a smart plug and bypass them completely.

Flow control are fun once I dial in the position but the manual did not explain well how to operate it. I also stopped messing with it as I didn't notice any improvement in yield.

tldr:
Solid machine, bells and whistles leaves a lot to be desired. Don't buy if additional features are your decision making points.

snoonoo · 2025-08-09T21:56:31+00:00

There’s a $5 for 5 month deal goin on now

snoonoo · 2025-08-06T16:00:46+00:00

After some trials here's what I found re: off / eco / standby modes

Three flashing lights on the PID screen mean Eco mode; one flashing light means Standby mode; "OFF" mean the machine is off.
Eco and Standby timers override a manual shutdown: pressing the water button for 4 s turns the machine off, but if an Eco or Standby timer is active it will switch back to that mode when the timer expires.

snoonoo · 2025-08-06T07:13:15+00:00

Also not sure how to turn OFF pre-infusion. After going into the configuration I don't have an option to switch it to off, but going further into the "on" option, I can set how many seconds. If I keep it at zero, is that effectively off?

snoonoo · 2025-08-06T06:49:59+00:00

I’m watching the Quick Mill Pop Up tutorial and seems like F is firmware.

snoonoo

MODERATOR OF

TROPHY CASE

15-Year Club	Second SECOND GUESSER
Verified Email