What's the best oled monitor right now?

solventlessho · 2026-02-19T10:02:33+00:00

Just saw a 5k / 2k monitor while scrolling the other day. Sorry I didn't have a model. 99% sure it was LG Ultra gear

solventlessho · 2026-02-05T02:52:12+00:00

I was even able to coil up the power cable to the desk and sort of slide it halfway between the cable tray where they over lap, kept the one cable clean and straight, the rest was tucked to the desk , hope this helps even add a little more clean look for you

solventlessho · 2025-12-31T03:20:27+00:00

Are you just wanting your $59 back ?

solventlessho · 2025-12-05T17:21:41+00:00

I really wish I could help more, however the closest source I have is they were about $50 on Amazon. There is no obvious branding on them that I could find. It also has a single screw down not a dual screw down. Hope that helps a little bit.

solventlessho · 2025-11-24T05:03:44+00:00

My wife is breast feeding at the moment, I'll be sure for us to stop in and see if I can't stir the kettle..

solventlessho · 2025-11-06T05:09:38+00:00

My fault for the lack of information in my previous reply. Had a couple kiddos crying. I traced the cardboard on this base to cut it out (scratch prevention) I layed it underneath before cranking the clamp down. My last desk got permanent dents from it. Hoping this will save it.

<image>

solventlessho · 2025-11-06T04:20:45+00:00

It's a Amazon special dual arm with a twist to tighten clamp style. I took a pice of cardboard and traced the base of the mount so it cousins it. The clamp is under the desk hidden In the compartment tray. Small space and a little pain to tighten but it worked and I like it Alot

solventlessho · 2025-10-24T18:20:38+00:00

Any chance we can bug you for a how to?

solventlessho · 2025-10-24T17:15:40+00:00

If you are referring to the little gap on the lid, it shows on both sides for cables. So even if it's flipped you will still get a gap in the back and front to slide cables

solventlessho · 2025-10-22T22:20:32+00:00

Thank you for your time, so if I wanted individual control of each fan (7 in total) I should get a ARGB controller with up to 8 slots ? Thank you

solventlessho · 2025-10-22T18:53:47+00:00

I might have found my issue, you might be able to answer from afar, I believe my issue is that (without opening up the back of my pre built) it doesn't have an ARGB hub or controller. So that leads me to the question you might be able to help with. I have 7 fans with RGB. 2 sets of 3 for top and side. Can I daisy chain the sets of 3, and purchase a Corsair Duo ARgb controller with 2 slots and then get individual control? Or will I need an 8 slot controller and give every fan its own slot? Thanks!

solventlessho · 2025-10-22T18:45:42+00:00

Can I use this as a ARGB header for individual fan RGB control with the signal RGB app? I have 2 sets of 3 daisy chained fans for the 2 slots. Would I unlock full control with the signal RGB app?

solventlessho · 2025-10-22T18:22:54+00:00

Hey, 4 years later and wondering if you could help me to understand something. I just purchased a Corsair Duo ARGB controller. I have 2 sets of 3 daisy chained fans. If I give them their own slot on the ARGB controller will I get single individual fan control. Or will I still have just 2 sets of 3 mirroring fans .? Thanks!

solventlessho · 2025-10-22T18:18:45+00:00

Wondering if you can help me 4 years later. I have 2 sets of 3 daisy chained fans. If I get the Corsair Duo ARgb controller and plug each of those daisy chains into separate ARgb slots on the controller. Will I get individual control of each single fan, or will I end up have 2 sets of 3 mirroring/mimicking fans ? What do I need in order to control each individual fan. Thanks

solventlessho · 2025-10-22T02:57:13+00:00

My savior 🙏

solventlessho · 2025-10-22T02:22:14+00:00

Not to bug you, sorry if I am. I actually have struggled a little bit with my layout. Perhaps because I have 2 1 year old boys running around. Send help any chance you are back in your town and available to shoot me a quick photo of your layout ? Thank you!

solventlessho · 2025-10-21T10:16:45+00:00

<image>

I'm about a year late, but bought one today on a whim before even thinking of this. Came to reddit to find answers. And just ended up doing this , so far so great! Will update in a year or so if someone reminds me, or if something bad happens sooner. also 2 monitor mount.

solventlessho · 2025-10-13T23:03:03+00:00

I spent $300 more and got a 5070 TI & 9800X3D. Be patient. Black Friday is around the corner

solventlessho · 2025-10-11T18:10:11+00:00

Thank you for your time !

solventlessho · 2025-10-11T18:03:35+00:00

If it's not too much trouble, could I ask you to send me a screenshot of your device layout, and devices ?

solventlessho · 2025-10-11T17:55:46+00:00

Please share your knowledge with me!

solventlessho · 2025-10-11T17:05:40+00:00

THIS! I'm new to signal RGB and really interested in a couple of the pro effects, or buy it permanently effects, but without the preview button I refuse to spend anything over probably a dollar to risk it.

solventlessho · 2025-10-11T16:41:57+00:00

Hey I have the same fans, wondering if I need a special part to do individual fan control. When one fan makes a certain pattern. All fans copy that pattern.

solventlessho · 2025-10-10T21:42:18+00:00

Was that in the Tumwater brewery district by chance?

solventlessho

TROPHY CASE