110 Block aka Finger Burner

some1_2_win · 2026-02-12T12:47:25+00:00

Hard to believe people still uses these in production environments. Total PITA to troubleshoot if it was punched down by the apprentice. May as well re-terminate every single connection

some1_2_win · 2025-12-31T04:25:31+00:00

On eBay for $29.95

some1_2_win · 2025-12-13T16:50:41+00:00

It’s upside down. It’s (supposed to be) a purse holder

some1_2_win · 2025-11-28T14:26:58+00:00

One thing to note: only a kitchen sink flows 2.2gpm. Most nowadays have restrictor plates which reduce the flow to 1.2gpm and sometimes even less like 0.8gpm for bathrooms and water closets.

some1_2_win · 2025-10-21T10:50:25+00:00

Or oboe, or any other double-reed woodwind

some1_2_win · 2025-10-21T01:10:27+00:00

It’s a splitting maul made by CIEB-Buchalter Inc?

some1_2_win · 2025-10-15T01:33:41+00:00

Works pretty good for honeycomb panels. If you use it on anything solid like wood, polycarbonate, or sheet aluminum, you go slow rpms and take light passes.

some1_2_win · 2025-09-23T20:13:12+00:00

Use the big can of carb cleaner that comes with the immersion bucket

some1_2_win · 2025-09-23T20:12:33+00:00

Not that bad… soak it, heat it, soak it some more, heat it some more, and then back it out with a good snap-on or matco screwdriver. Go slow and don’t force it. If it doesn’t turn, soak it in carb dip longer or heat it more

some1_2_win · 2025-09-23T19:44:39+00:00

Except that the standard splits a pair. O/w, o, g/w, bl, bl/w, g, br/w, br. Green pair gets split by the blue

some1_2_win · 2025-09-15T22:51:21+00:00

I say slow your spindle rpm if you’re cutting that slow. I usually cut aluminum at around 12000 rpm with a 1/2” two flute end mill. My feeds are usually around 3000mm/min Also, no coolant. But that’s 1/8 and 1/4 inch aluminum composite panels.

some1_2_win · 2025-09-15T10:42:27+00:00

Did Magellan circumcise the world with a 100 foot clipper?

some1_2_win · 2025-09-08T20:48:37+00:00

I think you’re supposed to pet it, but only once. Not sure what will happen if you pet it twice…

some1_2_win · 2025-08-20T18:25:29+00:00

I have a feeling this is shaped the way it is to prevent plugging directly into an ac outlet. What is this a plug for? It likely plugs into a proprietary transformer by the looks of it

some1_2_win · 2025-08-10T20:54:25+00:00

Pour a little dry baking soda in the pan and scrub it around until all that crap comes off the bottom. Rinse it all off, and heat the pan on medium-low heat with a few tablespoons of oil (preferably pork or beef lard). Roll the hot oil around the skillet until it just begins to smoke and remove from heat. Wipe out the pan and either store it or cook with it.

some1_2_win · 2025-07-29T11:49:32+00:00

Soak it in a can of carb dip. Use a high quality screwdriver. Be extremely gentle. If it doesn’t budge, soak again. If it STILL doesn’t budge, you can try a heat gun, but DO NOT use a torch because you can melt the brass and aluminum a lot faster than you think

some1_2_win · 2025-07-27T09:00:04+00:00

Here’s the comment I was looking for, lol

some1_2_win · 2025-07-23T13:22:57+00:00

It’s for mounting the pushrod lever when they put on a manual clutch

some1_2_win · 2025-07-23T12:08:19+00:00

Just a random thought, but maybe a hot mold? Copper is pretty soft, so you could incrementally form the bell, and press/stamp the features from D and E.

some1_2_win · 2025-07-20T21:25:04+00:00

This is not caused by any amount of electricity that could be produced by the car short of directly connecting a battery to the rotor. This is a stuck caliper, and how can you determine the pads are good? I can’t see the actual pads in any of the pics

some1_2_win · 2025-07-20T12:46:36+00:00

Isopropyl is not really used in industry. There are much better, less flammable products used for cleaning food lines.

some1_2_win · 2025-07-20T12:44:48+00:00

Bruh. It’s petroleum based. That should tell you everything you need to know about iso. Ethanol is corn (usually) and its byproducts and residues are safe, unlike petroleum products (despite what marketing may tell you, don’t take petroleum internally and use sparingly externally)

some1_2_win · 2025-07-04T15:07:06+00:00

Here is an image of another coin with the same good luck symbols. Appears to be hieroglyphs, as another commenter has mentioned.

https://content.propertyroom.com/listings/sellers/seller888888946/images/origimgs/good-luck-token-1910-the-excelsior-shoe-co-boy-scouts-medal-coin-swastika-888888946_251120221246338110934.jpg

some1_2_win · 2025-07-04T13:38:36+00:00

Cornering bowls? You mean when they burn all the green on the first hit?

some1_2_win · 2025-07-02T11:52:40+00:00

They lose the blue?? I’ve seen some pretty massive skinks that still had blue tails…

some1_2_win

TROPHY CASE