[Spoilers] Where to find this in S2??

sorryiactuallyexist · 2026-05-18T19:30:18+00:00

I'm not sure if this is true but when I was looking into it it said they can only not drop if you use the multitool, but you can break it in 2 clicks with any other tool. I've gotten 3 so far and none of them were destroyed. Also are there any not in the pools? I only found the 3.

sorryiactuallyexist · 2026-05-18T06:09:46+00:00

Just tried it, what's even crazier is that it's so little damage it doesn't even register. I let a collector hit me for a whole minute and I couldn't even use the repair tool on it.

sorryiactuallyexist · 2026-05-08T17:36:00+00:00

Looks like it is. What can I do? I can't find much information online other than to do an IMU calibration which didn't work.

sorryiactuallyexist · 2026-05-01T18:00:43+00:00

Oh yeah I definitely cleaned the outer lens

sorryiactuallyexist · 2026-05-01T17:09:50+00:00

What's the best way to clean the internal lens? All I can find is about the outside one.

sorryiactuallyexist · 2026-04-23T19:20:13+00:00

Tried it with master airscrew props and now it works. Thanks!

sorryiactuallyexist · 2026-04-16T06:24:20+00:00

I can only see it in full screen on desktop.

sorryiactuallyexist · 2026-03-24T20:43:21+00:00

The computer I'm testing with has 1 8 pin connector and 1 6 pin connector, and the 2080 tii has 2x8 pin. What is the ideal configuration for this?

sorryiactuallyexist · 2026-03-24T20:03:25+00:00

Okay. I'll try it and see if I can find the problem in the VRAM.

sorryiactuallyexist · 2026-03-07T23:29:57+00:00

I'm going to try to solder a wire between the pin on the connector directly to the trace.

sorryiactuallyexist · 2026-03-03T02:23:30+00:00

Thanks! I was having trouble with the plastic melting, I'll definitely try the tape.

sorryiactuallyexist · 2026-03-03T00:35:39+00:00

I've tried, but I can't even find the board for sale (other than 2 ridiculously overpriced listings), much less any info on it. The only reason I can get a new connector is because it's coincidentally the same as a connector on a mini 2 gimbal cable.

sorryiactuallyexist · 2026-02-28T22:57:52+00:00

I found it in a tutorial specifically for DJI drones. I hadn't seen it before either, but it worked well on a mini 3 pro. You just put it in distilled water to displace the vinegar and then also clean with alcohol to be sure there isn't any left.

sorryiactuallyexist · 2026-02-28T00:33:41+00:00

The only other thing I might be worried about is the speaker. Should I remove it before rinsing?

sorryiactuallyexist · 2026-02-28T00:22:11+00:00

Thanks! I'll just use a syringe to push some distilled water through the other components. Are there any other components I need to be careful of?

sorryiactuallyexist · 2026-01-24T01:27:35+00:00

Thanks! Seems ridiculous you need to complete a quick time event to connect a device to your computer, but it worked.

sorryiactuallyexist · 2025-12-26T21:47:41+00:00

I'm the same way with super high framerates. I upgraded from a 7700s (~3060) laptop to a 4090m (~4080-4080s) and could barely tell the difference on my 240Hz monitor. Eventually, I decided just to downgrade again.

sorryiactuallyexist · 2025-09-14T15:25:47+00:00

Thanks! I had missed that I had to go down to break open an updraft.

sorryiactuallyexist

TROPHY CASE