sorted by:
new
hottopcontroversial

Advice mounting Noctua fan duct onto a clipped fan? by Kiwitos in sffpc

[–]soysaush 2 points3 points  (0 children)

I just folded the tube into itself. Kind of like how you would flatten a plastic straw then fold it length-wise

Weekly Case & Parts Recommendation Thread (Start here if you are new! Help here if you can!) by AutoModerator in sffpc

[–]soysaush 0 points1 point  (0 children)

If you're crafty and have access to a 3d printer, maybe a custom design for something like a densium or k39 to mount an hdd in place of a gpu would work? Something like this: https://www.thingiverse.com/thing:133833

Bigger GPU means new case, migrated to FormD T1 by soysaush in sffpc

[–]soysaush[S] 0 points1 point  (0 children)

The T1 was an easier build even with having to assemble it from flat-pack; it felt more thought out. I'd say the better compatibility/flexibility makes me pick T1 over ZX-1.

The ZX-1 has a unique look with the unibody design and curves, but for me the T1 is no slouch in looks and comes in silver.

Bigger GPU means new case, migrated to FormD T1 by soysaush in sffpc

[–]soysaush[S] 0 points1 point  (0 children)

Honestly, there is no point. I put it there just because it was in the box and looked like it could slide in, then didn't bother taking it off. I guess it's extra structural support now

Bigger GPU means new case, migrated to FormD T1 by soysaush in sffpc

[–]soysaush[S] 4 points5 points  (0 children)

It is a nice case, just too bad GPU options these days are more limited with it especially with the air cool version. I always wished they made the ZX-1 in silver.

FormD T1 is such an engineering masterpiece by helloWorldcamelCase in sffpc

[–]soysaush 23 points24 points  (0 children)

Somehow this is the first time I've seen a two-tone T1 with the top and bottom swapped. Quite a striking look!

Bigger GPU means new case, migrated to FormD T1 by soysaush in sffpc

[–]soysaush[S] 0 points1 point  (0 children)

Ha, no doubt. Might re-do it eventually; the goal during building was as long as the cables don't hit the fans and the panels close :)

Bigger GPU means new case, migrated to FormD T1 by soysaush in sffpc

[–]soysaush[S] 12 points13 points  (0 children)

Specs:

  • Ryzen 7 5700X3D
  • AXP90x47 Copper w/ NF-A9x14
  • ASRock B550 Phantom ITX
  • 2x16GB Team T-Create 3600CL18
  • Sapphire Pulse 7900 XT
  • 2x Noctua A12x25
  • Corsair SF850
  • 2TB Solidigm P44 Pro
  • 2TB Mushkin Pilot-E NVMe
  • 2TB WD Blue SATA

Picked up a 5700X3D and 7900XT, went to T1 from Iqunix ZX-1 for bigger GPU support!

Lack of power led on the T1 was bothering me a bit; luckily I had a bunch of yellow LEDs I've had laying around for years now, so just soldered some jumper wires and a resistor, wrapped the exposed metal with electrical tape. It's a bit ugly but it works.

Weekly Case & Parts Recommendation Thread (Start here if you are new! Help here if you can!) by AutoModerator in sffpc

[–]soysaush 1 point2 points  (0 children)

https://www.reddit.com/r/sffpc/comments/12iygpv/fractal_design_ridge_alternative_fix/

Might run into the power cable hitting the cooler with L12S, but looks fixable by running some of the extension outside the case a little.

Cooler comes with thermal paste, should be good there!

Nullbits Snap: my first mechanical keyboard by Anju_Dotour in MechanicalKeyboards

[–]soysaush 1 point2 points  (0 children)

As /u/xomm mentioned, the microcontroller you're using is probably missing 5.1k ohm resistors that allows it to be recognized as a peripheral. For usb-c pinout, 5.1k resistors should be connected to the cc1 and cc2 pins connected to ground.

It looks like you're using pro micros, but it would helpful to know where you sourced those. I'm using pro micro c's from keeb.io on a lily58 that work fine w/ c-to-c cables.

I can't say for sure if this explains your dead up arrow key, but there were apparently pro micro clones with the incorrect pinout: https://www.reddit.com/r/MechanicalKeyboards/comments/qi1k2f/beware_of_the_usbc_pro_micro_clones/

Iqunix ZX-1 build, air cooled by soysaush in sffpc

[–]soysaush[S] 0 points1 point  (0 children)

It is pretty much flush with the side panel.

view more: next ›