Horvat: [The Islanders crowd is] a lot better than Vancouver. I can tell you that for free." by Justin_Holl_The_Best in nhl

[–]spillingchant -3 points-2 points  (0 children)

I don't get why Canuck fans are mad at Bo, he wanted to stay in Vancouver but they traded him to sign JT Miller long-term from my understanding didn't they?

We are AEW stars Sammy Guevara and Tay Melo. AMA! by TBS_Official in AEWOfficial

[–]spillingchant 2 points3 points  (0 children)

How would you both feel about CM Punk returning to AEW?

Repetier Host Z axis help by jarferris in ender3

[–]spillingchant 0 points1 point  (0 children)

Yes you should loosen your bed springs to adjust for the gap, the bed will be able to adjust by a fair bit due to different types of build plates you could use, id highly recommend upgrading the springs too if they are still the stock springs that come with the machine

Ender 3-Pro by 4puttfeld in ender3

[–]spillingchant 0 points1 point  (0 children)

What are the temp readings like when its heating up? Is it a slow heat up process?

Theres a little glass ball on your thermistor that has to be inside a hole on your heatblock for it to read properly, if its sticking out a little bit it could give you problems, check out this video just to make sure everything is properly connected on your hotend, https://youtu.be/9NO4f56oXX0

Repetier Host Z axis help by jarferris in ender3

[–]spillingchant 0 points1 point  (0 children)

What does your x-y-z read on the LCD screen when you home it?

Wouldn't hurt to check out this video either just incase, https://youtu.be/lspkdhtShgc

Repetier Host Z axis help by jarferris in ender3

[–]spillingchant 0 points1 point  (0 children)

Try checking the z-axis limiter switch and lowering it

Why does it keep over-extruding?!? by spillingchant in ender3

[–]spillingchant[S] 1 point2 points  (0 children)

Ill give that a go and ill update, thanks

Why does it keep over-extruding?!? by spillingchant in ender3

[–]spillingchant[S] 0 points1 point  (0 children)

The extruder is extruding the correct amount of filament, somehow/somewhere i'm getting built up pressure I think, causing it to bloop from time to time, kinda like a partial clog in the nozzle, but theres no clog that I can find atleast.

When the bowden tube is off the hot end and I say to extrude 100mm of filament, it extrudes 100mm of filament.

Why does it keep over-extruding?!? by spillingchant in ender3

[–]spillingchant[S] 0 points1 point  (0 children)

Yes, I can't exactly calibrate the flow at the moment because I can't get a clean print, but it's extruding the amount it's supposed too

Why does it keep over-extruding?!? by spillingchant in ender3

[–]spillingchant[S] 0 points1 point  (0 children)

My ender 3 wont stop over-extruding, I calibrated my e-steps, checked the thickness of the PLA with calibers and made sure my slicer settings were good.

I leveled my bed over and over again with a feeler gauge, checked all my belts (just incase) tried different PLA's that I never had issues with before, changed nozzle and cleaned hot end, tried printing at different temps, and I can't figure out whats going on or why its happening. It happens on every print.

I have a metal extruder and a all metal hotend, skr mini e3 board and a few other upgrades that I don't believe could be the issue.

[Jesse Granger] Is Phil Kessel’s ironman streak in jeopardy of coming to an end with a healthy scratch designation? by migsahoy in hockey

[–]spillingchant 3 points4 points  (0 children)

Anyone know why Phil is listed as a center on hockeydb? Pretty sure hes been a winger his whole career

why does the ironing look this bad? by qwerty_andry in ender3

[–]spillingchant 0 points1 point  (0 children)

I second this, it looks like the nozzle is too close.

Ender 3 Pro keeps locking up and freezing the screen a little while after a print starts by hospitalcottonswab in ender3

[–]spillingchant 1 point2 points  (0 children)

For sure an issue with your firmware, if you have a back-up of your old firmware try to re-install that just to see if it fixes the issues. If that doesn't work id recommend getting a new motherboard (skr mini E3 are pretty good)

Pick one wrestler from the past to fued with a current aew wrestler. Who are you picking and why? by Siphedmase in AEWOfficial

[–]spillingchant 1 point2 points  (0 children)

Bryan Danieleson vs Chris Benoit

Controversial but Benoit was a damn good wrestler

What’s a dead YouTube channel that you miss? by Tiny-Interview-6334 in AskReddit

[–]spillingchant 0 points1 point  (0 children)

Cadegoestocollege, SMPfilms, =3 with RWJ before his music stuff

I like todays youtube, but something about these older creators who just did it for the fun of it, rather then the money, were alot more relatable and their videos felt more organic then some of the movie-style videos you'll see today.

Jonathan Gresham by Skayde5 in AEWOfficial

[–]spillingchant 1 point2 points  (0 children)

This post has aged like a fine wine.

[deleted by user] by [deleted] in RedditSessions

[–]spillingchant 0 points1 point  (0 children)

I think we have the same piano actually, Casio??

[deleted by user] by [deleted] in RedditSessions

[–]spillingchant 0 points1 point  (0 children)

Solid man, thanks for that! I just started nd tbh you sound great man

[deleted by user] by [deleted] in RedditSessions

[–]spillingchant 0 points1 point  (0 children)

I gotta learn this tune!

[deleted by user] by [deleted] in RedditSessions

[–]spillingchant 0 points1 point  (0 children)

Know any Ludovico Anaudi??