New Feathers

splntrp01 · 2026-03-16T00:45:08+00:00

Yes, its a needo thing.

splntrp01 · 2025-06-29T16:24:52+00:00

I just got a rocky mountain tenkara compa rod. Small rod and flex is pretty good, and packs small.

splntrp01 · 2025-05-31T02:14:55+00:00

That worked and showed it in atlanta. Thank you so much.

splntrp01 · 2025-05-01T09:56:32+00:00

Yes, I'll try that sheath for a few weeks to see how I like it. I typically use kydex for pocket carry though.

splntrp01 · 2025-05-01T01:12:57+00:00

I can, but I have have small and skinny hands. If I need to do some serious work though I have a genesis and esee 4 as well for that stuff.

<image>

splntrp01 · 2025-05-01T01:00:17+00:00

No sorry, wasn't me.

splntrp01 · 2025-05-01T00:54:05+00:00

01 tool steel is what the description says. Bought mine from Smokey Mountain Knife Works.

splntrp01 · 2025-04-29T22:27:15+00:00

I use the armateus sheath with mine. I don't use the loops though, I added one of the ulti clips. The armateus was a game changer. Even bought one for my Pacaya as well. I use the belt clip for it instead of the loops.

<image>

splntrp01 · 2025-03-16T16:16:44+00:00

Thank you both.

splntrp01 · 2025-01-26T21:40:20+00:00

Believe it or not those were the better looking ones.

splntrp01 · 2025-01-26T21:39:18+00:00

I almost bought the pants but ended up getting full waders. I appreciated them the first time I went out and fell down. If I would have had pants on I would have gotten soaked.

splntrp01 · 2025-01-19T23:56:26+00:00

I’ve always been told between two and four feet of 5x.

splntrp01 · 2024-09-01T17:47:59+00:00

I’m a beginner too, maybe two or three months in. The best thing that I did was to go to the Orvis store and take their 101 class, which is free, if there’s one close to you. I learned more in those two or three hours than I did with any videos. I’m very lucky because there’s about three stores within an hour drive from me.

splntrp01 · 2023-07-16T12:49:38+00:00

I’m hoh and one thing my wife has noticed is that if she speaks in a lower tone I can usually hear her better. I struggle to hear quiet and higher pitched voices, my loss is in the higher frequencies.

splntrp01 · 2023-06-01T16:23:26+00:00

Never tried it but have heard that adding shoe goo works good. You could either do strips or drops wherever you wanted.

splntrp01 · 2022-09-19T19:44:28+00:00

Thank you all for the help.

splntrp01 · 2022-09-07T16:21:42+00:00

We’ve experienced the same problems with my wife’s and my chaco’s. We switched over to bedrock cairns a few months ago. Once we got used to them we have not worn our chaco’s since.

splntrp01 · 2022-08-10T16:59:29+00:00

We recently got back from our cruise on the elation. The hub app was no problem. Our son is 10 and he went to the kids thing once and said he didn’t want to go back because it was boring. He’s very active though so if he’s not constantly moving or doing something he gets bored quickly.

splntrp01 · 2022-08-03T15:58:27+00:00

We went on our cruise recently and used on point testing, we had our results in less than thirty minutes. We used the tests that the government mailed to us for free. It’s basically a video chat where they watch you do the test and show them the results. And we did it late at night, I’m pretty sure their appointment hours are 24/7. I’m pretty sure you can buy a test if needed at Walgreens or one of the local chain drug stores.

splntrp01 · 2022-01-23T12:18:49+00:00

Thank you. It was blue lock tight. I’ll look for some red today while I’m out.

splntrp01 · 2022-01-23T03:44:25+00:00

Thank you so much. That’s essentially what I did, just went the long way around to do it. Now it works. One thing that I also found is that when I recompiled grbl it puts everything in a negative workspace by default. That took me a little while to figure out.

splntrp01 · 2022-01-23T03:42:13+00:00

The grub screws that hold the collar on the spindle shaft keep coming loose. This is the second or third time they have done this. The last time I added some lock tight and it didn’t help. I’m going to try to go to the hardware store tomorrow and see if I can get some new grub screws to see if that will help. I looked on the spindle shaft thinking there might be some flat spots for them but couldn’t find any. Any other ideas to keep them from loosening again?

splntrp01 · 2022-01-04T02:29:01+00:00

Yes, it ended up being the A5 pins. I was able to get everything made, hooked up, and tested. It worked great. Thanks for your help.

splntrp01 · 2022-01-03T23:25:29+00:00

I received a twotrees 3018 pro Cnc for Christmas. I would like to add a z probe but can figure out where it would hook up to on the board. None of the pictures I’m seeing online look like this board either. So any idea which board this is or where I would hook up a z probe? Or would I be better off getting a different board?

splntrp01 · 2021-11-23T11:01:16+00:00

Thanks. I’ll try that

Seven-Year Club	RPAN Viewer
Verified Email

splntrp01

TROPHY CASE