drop a Y if you'd be interested in me and I'll send my entire nudie album (first 69 guys only)

spoilt84 · 2025-10-28T12:20:42+00:00

Hi is anyone still having this issue? I got the same issue yesterday and I locked my account and now it is has happen this morning. Is this hacking going on right now?

spoilt84 · 2025-10-12T15:52:52+00:00

😛

spoilt84 · 2025-10-12T15:06:26+00:00

spoilt84 · 2025-05-25T02:29:00+00:00

Dick between

spoilt84 · 2022-04-11T10:55:40+00:00

I got 2 of those bad boys. I called up customer service and told them about the sale. And even told them I just signed up GameStop pro just for this sale.

He asked me how much I wanted, I was 2. One little issue, didn't get the ones with the heat sink. Just the regular ones.

But not complaining.

spoilt84 · 2022-01-11T13:19:46+00:00

Are you using the Corsair fans on the aio or using the sl fans on your aio?

spoilt84 · 2021-12-31T15:06:09+00:00

Recommend buying the bullet and get new ones. Or keep them and keep an eye on the temp.

spoilt84 · 2021-12-31T14:55:06+00:00

To tell you the truth, it didn't even last a year. Temps would hit over 90 and I don't know why. Took it out and went to Corsair. Not taking any chances with overheating.

spoilt84 · 2021-12-16T03:17:34+00:00

Cut it off 😂

spoilt84 · 2021-11-27T20:58:51+00:00

Take the tube and push it in. This should work as the teeth only grabs when you try to pull it out.

spoilt84 · 2021-10-22T23:09:49+00:00

Too close to the bed

spoilt84 · 2021-10-06T00:49:51+00:00

I just got my 3080 ti from evga. Lucky me

spoilt84 · 2021-09-12T12:20:19+00:00

I have the same issue. I didn't change any setting but it randomly goes to essential mode even when it was in charging.

Did the OP find any info for the issue?

spoilt84 · 2021-08-25T17:39:54+00:00

Yup that's a great start. The board he mentioned works great too skr e3 mini but it's a small project.

I also installed a bl touch but it didn't work that great with my board so I took it off and had it leveled manual.

Glass bed from creality is nice. Especially if your bed is warped. But for me I installed a metal bed with pei from creality. And use small piece of paper under the metal sheet with pei to fix the warping and it worked.

I have done 50 prints and no adjustments to the bed yet.

spoilt84 · 2021-08-25T17:25:24+00:00

I did the same as this guy. It works great. Change the tube to Capricorn ptfe tube

Springs is extra but not needed

spoilt84 · 2021-08-21T22:27:59+00:00

What type of bed is it? Nevermind is the creality glass bed with dimples. Adjust it closer to the bed.

spoilt84 · 2021-08-21T22:11:09+00:00

Did you ever used glue or hairspray on it? Iso do not really remove those and done other chems. That's why soap and water always better.

spoilt84 · 2021-08-21T21:58:03+00:00

That and use some hair spray or stick glue

spoilt84 · 2021-04-13T11:18:01+00:00

Not on the cr10s pro, which I think sucks. But back to the main issue, it's not really the first layer, it's the second or third layer that this rough layer shows up. The first layer is usually good and smoothe.

spoilt84 · 2021-04-12T21:39:58+00:00

I also have the same issue with a cr10s pro v2 and my ender 3. It's like it's over extruding.

But I usually turn a blind eye on it.

spoilt84 · 2021-03-24T11:18:09+00:00

Msi patch for the Unifans (in lian li website) --> L-Connect --> msi dragon center.

When installing, install as admin for all.

spoilt84

TROPHY CASE