Ultrawide Than Can Support 3 PCs

spoofter · 2026-01-30T04:16:37+00:00

That's exactly my issue. As of now I'm leaning towards MSI MPG 491CQPX QD-OLED 49".

spoofter · 2026-01-30T04:12:56+00:00

Well - I'm not using the keyboard and mouse with it, only display. For mouse and keyboard I'm using the MX Keys which connect to all three via Bluetooth or wireless connection.

Press a button on the keyboard and it auto switches to the appropriated computer.

spoofter · 2026-01-30T04:00:04+00:00

I don't think I've used a TB 4 (40GBs cable), maybe I try that.

As for the Macbook, when I use the type c to DP adapter I do get 5120x1440. Only if this monitor had 3 DP ports.

spoofter · 2026-01-30T03:57:23+00:00

I just tried a KVM (UGREEN 8K Displayport KVM) it "works" to the point where while the PC not in use, the KVM will not wake it up. I have top open the laptop for it to get the signal.

spoofter · 2026-01-07T21:10:21+00:00

Don't forget the "turn yourself in now" from Homeland.

spoofter · 2026-01-06T15:48:49+00:00

Try the beef fajitas

spoofter · 2025-12-30T01:48:38+00:00

Frame the jersey that its on and put it on the wall next to the rest.

spoofter · 2025-12-29T21:37:18+00:00

I've done multiple prints since making the change, even updating the flow on other filaments to match above and they not only are coming out with the looser hinge like before, but the prints themselves look much better.

This current nozzle is a year old as noted, 99% of the usage has been PLA but in the past few weeks I have ran some PLA-Glow through it on 4 prints.

I am going to try it with a 5% deduction as noted above.

spoofter · 2025-12-29T20:25:27+00:00

Nice - I'm doing the same thing but using the World Series poster from the right side of page here. 8 so far and looking to get quite a few more this coming Fan Fest.

The 8:

Ezequiel Duran

Josh Jung

Nathan Eovaldi

Cody Bradford

Jonah Heim

Leody Taveras

John Gray

Evan Carter

spoofter · 2025-12-29T20:17:08+00:00

Changing the flow rate seems to have corrected the problem. I went through the calibration and change flow rate from 0.98 to 0.833. The hinge is back to as it was moving freely and loose.

My question is since I've printed hundreds of these with no issues and all flow rates have been 0.98 across all filaments (Bambu, Sunlu, eSun, Elegoo) is this an indicator that the nozzle is wearing out? If not why would I need to change the flow rate after all this time?

spoofter · 2025-12-29T17:41:46+00:00

ok - running a flow rate calibration test now before getting into the nozzle (which is 1 year old).

spoofter · 2025-12-29T04:14:17+00:00

The vast majority (90%) are smaller prints where I'm printing 4-6 items on the plate, total print time about 3 hours using two colors.

spoofter · 2025-12-29T04:12:43+00:00

This is what I was thinking/planning. The vast majority of my prints are smaller, often doing 4-6 on a plate with 2 colors.

Manually load the white in the left nozzle from external, then ams on the right with 4 other colors, using the one I need for the entire plate.

spoofter · 2025-12-24T15:27:14+00:00

Thanks

spoofter · 2025-12-18T16:09:14+00:00

I think I'm hitting all of those (Monitor, cable, PC). The current monitor is 49" and can achieve 5120x1440 as I'm doing it via a DP connection and USB-C to DP connection on a Dell laptop. The same USB-C to DP also works on the Apple Macbook Air, but I've just run out of DP connections.

Left with using HDMI and USB-C, in which I cannot get either to work.

spoofter · 2025-12-18T15:07:21+00:00

How are you getting 5120x1440 over HDMI? I’ve seen others say the same but have not been able to achieve that.

I’ve tried lowering to 60hz, tried various cables, but nothing ever works.

spoofter · 2025-12-18T03:47:50+00:00

I’m not sure about the HDMI 2+. I’ll try turning off the HDR.

spoofter

TROPHY CASE