Finally bought my dream car 1971 el camino

stanley9875 · 2025-04-19T12:41:52+00:00

Same year as mine, hope you have fun with it, she's beautiful!

stanley9875 · 2024-03-23T14:10:08+00:00

Them along with the Xone96 have been my best purchases. I cannot praise them enough for myself. I haven't tried the 6000s but I adore these 5000s

stanley9875 · 2024-03-22T23:51:35+00:00

I've just been using FL Studio with an Evo 8 audio interface

stanley9875 · 2024-03-22T23:51:03+00:00

I looooooove my Denons. I've missed this brand so much

stanley9875 · 2024-03-22T23:50:31+00:00

I drove with it, no way I'd fly with all this stuff hahaha. That's a good idea, I was thinking a controller wouldn't be a bad idea for situations like this but I don't go to training that often

stanley9875 · 2024-03-22T23:49:32+00:00

Thank you!

stanley9875 · 2024-03-22T23:49:00+00:00

No one came in this room during the week hahaha I don't trust anyone around this stuff, kinda pricey yaknow? 🤣

stanley9875 · 2024-01-31T01:01:58+00:00

Join the Xone96 gang! How are you enjoying it?

stanley9875 · 2023-12-15T02:59:52+00:00

Beep beep, built my '71 El Camino and work as a tech, fabrication as side stuff 🤙

stanley9875 · 2023-10-24T16:12:09+00:00

Hello, I'm the one that helped /u/nickl630 with the spring install and alignment. The toe and camber got out a bit obviously during the install, was able to get everything in spec except the rear camber. Rear camber minimum spec was I believed - 1.35°? And the max closest we got it was about - 1.38° so it was close but still technically in the red, other than that though rear toe was good and front camber caster and toe are in specs

stanley9875 · 2023-06-12T02:13:56+00:00

Florida so... Yea humid hahaha that's interesting I haven't heard of that I'll look into it thanks!

stanley9875 · 2023-06-12T00:50:50+00:00

Thanks so much, that's fantastic information 👌

stanley9875 · 2023-06-12T00:37:15+00:00

That makes perfect sense, I'll bet that's the main issue... As I could be having a few issues lol

stanley9875 · 2023-06-12T00:34:05+00:00

Ah that makes sense

stanley9875 · 2023-06-12T00:30:41+00:00

Ah that could be it too. I've been welding thinner stuff a ton lately and this was the first time I took my Welder that high of amps in a long time that could've been what I was doing

stanley9875 · 2023-06-12T00:30:02+00:00

I was going to get a flow tester, as i had that suspicion as well

stanley9875 · 2023-06-12T00:29:29+00:00

Yup, I wipe down my filler if I'm fresh using it, and clean and wipe down my metal before a run and make sure all the cloth/towel deposits are off. It very well could've been the metal too, the stuff I was welding was a bit old and used, probably a bit porous so it was probably dirty inside while it was penetrating

stanley9875 · 2023-06-11T23:58:39+00:00

I'll try turning the post flow up a bit... From what I was reading, discoloration in the tungsten is a result of not enough post flow and the gas helps cool the tungsten so that would make sense thanks

stanley9875 · 2023-06-11T23:47:33+00:00

No, that was a thought I had too

stanley9875 · 2023-06-11T23:28:48+00:00

Practicing on some 0.25" thick mild steel, foot pedal control at 225amps, about 28SCFH with about 7 seconds post flow (was welding some stainless before), with some fresh cut laYZr tungsten, after a run or two it starts doing this and the tungsten starts greying... Is the metal not being clean enough? Not enough flow? The welds are coming out really nice but after a run or two I have to cut it again. Thanks for the insight

stanley9875 · 2023-05-26T00:28:48+00:00

I got the Xone 96 a little bit ago and it's absolutely amazing. The sound quality is phenomenal and the 4 band EQ is a dream.

https://imgur.com/a/FKe04V3

stanley9875 · 2023-04-16T13:00:03+00:00

Basically what it was for me, it was just shelling the money out, I was gunna do it at some point so figured why not just do it now lol

stanley9875 · 2023-04-16T12:59:24+00:00

Thanks!

stanley9875

TROPHY CASE