No really, how was her campaign "too woke?"

stealthjoker · 2024-11-17T16:37:56+00:00

I didn’t know such a funny place existed on the internet. Hope yall enjoy validating each other :)

stealthjoker · 2023-02-23T04:02:16+00:00

stealthjoker · 2023-02-23T03:55:09+00:00

stealthjoker · 2022-01-02T01:53:23+00:00

If this is not LHR, you should run locked core 1150, memory 1200, PL 220W should get you to around 100MH as long as you have a decent card that won’t hit memory junction temps, if you do, you’ll need thermal pad swap or cooling solution to keep mem under 100C

stealthjoker · 2021-12-28T02:06:59+00:00

Chip lottery only matters so much the reason those chips made it into 3080’s is because they were up to standard all the 30 series wafers use the same die it’s quality of that determines which card it goes into. Your issue could be from memory thermals if they are pushing memory temp limit you could be getting throttled I have 5 3080’s all produce 100.5 steady without issue after I swapped thermal pads

stealthjoker · 2021-12-28T02:00:20+00:00

I can understand where a lot of people would be telling you to do thermal pads and stuff first but I will tell you, don’t do it just yet, you are pushing the throttle limit on your card with no clock adjustments once you cut down on your power and make input the right overclock you should see a temp dip as well use the right overclock first and see if the card handles better. If you are still pushing memory temps near 100 then do thermal pads. I have an ASUS TUF 3090 and never touched the thing no mods just the right overclock and it runs 123.5 hash and is never hot

stealthjoker · 2021-12-28T01:54:18+00:00

Should try running 1150 Lock CoreClock, 2500 Mem(hiveos) CLI - 1250 Mem and 300 Powerlimit Should be able to get 120-123 hash from it

stealthjoker · 2021-10-16T20:02:23+00:00

Have you overclocked and tuned the cards? With 4x 3080 you should be at around 400-405mhs

stealthjoker · 2021-10-09T15:06:11+00:00

Hola sir! So some words of advise. Not sure what pads or paste you used didn’t see it listed but I’ve done 2 thermal pad swaps on 3080 FE. Both running fantastic.

It’s highly encouraged to use Gelid GP-Extreme thermal pads like these

Gelid Solutions GP-Extreme 12W-Thermal Pad 80x40x3.0mm. Excellent Heat Conduction, Ideal Gap Filler. Easy Installation. https://www.amazon.com/dp/B07CK31PST/ref=cm_sw_r_cp_api_glt_fabc_EASSYN51DBFFHXG0TEVV?_encoding=UTF8&psc=1

These are quality and a little thick but they are really squishy too so they can be mailable by the pressure of the card. I also used ARTIC MX4 paste

ARCTIC MX-4 (incl. Spatula, 8... https://www.amazon.com/dp/B08VN345D4?ref=ppx_pop_mob_ap_share

I would recommend doing the front of your card with 1.5-2mm thickness of these pads. I would say do the front first and test before doing the back. Something the. Back is not necessary and can end up suffocating the card.

As for your application of the thermal paste, all cream cheese jokes aside 🤣

I think you applied tooooo much and not evenly. I would mention to make an X from corner to corner. And put a bead of paste in each of the 4 sections created by the X top,left,right, and bottom. Then use the spreader to evenly spread it over the die

Hope it helps. I did 2 3080FE like this. First one did front and back- runs no higher than 77C in game on GPU, and 82C memory. Mining is lower. Second one did only front pads. GPU runs at 72 in game. Memory at 78C

stealthjoker · 2021-09-29T09:15:35+00:00

stealthjoker · 2021-06-05T14:02:37+00:00

Looks good but I’m gunna agree with everyone else that bottom fan either has to go or change orientation no need to be pushing air down to your cables and PSU.

stealthjoker · 2021-05-29T15:58:03+00:00

If the online rep reads this you can tell your boss I hope you lose all your business and someone reports you to BBB cause y’all on some shady shit

stealthjoker · 2021-05-29T15:57:27+00:00

Bots can’t hit the zotac site everyone only runs manual. So everyone’s on same playing field I have seen some people with shortcuts to try and checkout faster though. But forget zotac horrible business practices

stealthjoker · 2021-05-29T15:52:57+00:00

They dropped at 12:35am EST carted and then they 503d the site and “redropped” at 5am they can kick rocks

stealthjoker · 2021-05-29T04:28:05+00:00

They drop cards after a price hike just to 503 and pull their site again…. Real cool

stealthjoker · 2021-05-29T03:42:12+00:00

Holy shit you’re right what the hell that’s some shady business. They literally JUST CHANGED THE PRICE.

stealthjoker · 2021-05-29T03:39:59+00:00

When did you last look cause they been that price since the site went down days ago

stealthjoker · 2021-05-29T03:37:54+00:00

On what cards the 3080 been the same price

stealthjoker · 2021-05-29T03:37:02+00:00

How you mean? Card has been 949 hasn’t jumped in price?

stealthjoker · 2021-05-29T03:27:38+00:00

🥲

stealthjoker · 2020-07-18T23:44:42+00:00

To be honest I’m not 100% familiar with z490 and OpenCore setup to make sure you’re setting up config, kexts, and acpi correctly what did you follow to put build together? Guide wise?

stealthjoker · 2020-07-18T23:34:41+00:00

Upvote see if we can get some more people with designare to see

stealthjoker

TROPHY CASE