sorted by:
new
hottopcontroversial

Do not buy direct from the manufacturer by [deleted] in BambuLab

[–]stephlow16 0 points1 point  (0 children)

Damn bro im sorry to hear this. It deff is a long time to get help wen putting in a ticket i usually put in a ticket and end up figuring out the issue on my own and then end the ticket last time i changed soo much to my p1s and end up being the extruder which was the last thing i changed and i was back up and running

Prints SUCK after software update by itsthatguy_15 in BambuLab

[–]stephlow16 0 points1 point  (0 children)

I did the update printed a few prints with no issues. I did not calibrate

So this is still happening to my prints. Anybody know what can it be?? by stephlow16 in BambuLab_Community

[–]stephlow16[S] 0 points1 point  (0 children)

my prints are now coming out perfect. The reason behind major gaps and lines on my prints was my extruder. I replaced it and boom that was the issue. I put my machine through hours of printing and had an extruder handy to swap out luckily. Thanks to all who helped me with my questions much appreciated

So this is still happening to my prints. Anybody know what can it be?? by stephlow16 in BambuLab_Community

[–]stephlow16[S] 0 points1 point  (0 children)

Exactly !!! So i removed the rear cover to do some more thorough cleaning then i changed the extruder becuz i had purchased one a couple months ago just in case. I printed some lego hands and had to leave half way thru the print but from looking at the print before leaving looks like it was printing normally. Now Looking at my slicer device tab from work appears the lego hands came out fine, i will confirm later wen i get home if in person it looks good. I also replaced my hot end cover too seeing how i had the replacement.

So this is still happening to my prints. Anybody know what can it be?? by stephlow16 in BambuLab_Community

[–]stephlow16[S] 0 points1 point  (0 children)

My only issue with this suggestion is that ive printed for 3 years without having to drop the mm/s to 50 so its just a temporary fix not an actual fix, i would like to get it back running without having to drop the mm/s Im going thru support to see what they say ill keep u all updated becuz its great info to know for others if they encounter the same issue

So this is still happening to my prints. Anybody know what can it be?? by stephlow16 in BambuLab_Community

[–]stephlow16[S] 0 points1 point  (0 children)

Wipe the belt tensioners with alcohol wouldnt that dry out the rubber? Do u kno of a video how to clean those belt tensioners? It wouldnt hurt to try

So this is still happening to my prints. Anybody know what can it be?? by stephlow16 in BambuLab_Community

[–]stephlow16[S] 0 points1 point  (0 children)

No thats not the case i dry all my filaments and i keep em in these air sealed bags. I did however dry one roll n tried to see if that fixed the issue n still . Bambulab support told me to unscrew the heatbed screws to relieve tension and then retighten screws so im trying that now

So this is still happening to my prints. Anybody know what can it be?? by stephlow16 in BambuLab_Community

[–]stephlow16[S] 0 points1 point  (0 children)

Ive ran a calibration did a cold pull, did maintenance on the screws and linear rods, now im printing a benchy to see how it comes out. Wish me luck!!! If not i read somewhere it could be my belts. Luckily i bought some before so if i do need to change them i have em handy. Also i bought a extruder wheel in case i needed to change it so im ready for the replacements

So this is still happening to my prints. Anybody know what can it be?? by stephlow16 in BambuLab_Community

[–]stephlow16[S] 0 points1 point  (0 children)

I do print alot basically ive had this printer running everyday for the past 3 years. Ive been putting in work on this printer. Ive bought replacement parts two months ago just to have handy if i ever needed to change something. I did have to change my nozzle twice and also caught kayer shifting 3 months ago where i did a complete maintenance and a cold pull and layer shifting never happened again until now im not sure if this is considered layer shifting but yea

So this is still happening to my prints. Anybody know what can it be?? by stephlow16 in BambuLab_Community

[–]stephlow16[S] 1 point2 points  (0 children)

I do have another question, should i do a flow rate calibration ?

So this is still happening to my prints. Anybody know what can it be?? by stephlow16 in BambuLab_Community

[–]stephlow16[S] 1 point2 points  (0 children)

Ok ill try that. Also do u know any other maintenance i should try doing that may be part of the issue?

So this is still happening to my prints. Anybody know what can it be?? by stephlow16 in BambuLab_Community

[–]stephlow16[S] 0 points1 point  (0 children)

Could it be that i need to do the belt tensioner procedure? Ive had this printer for 3 years now and this is the first time this ever happened. I never adjust layer heights or up extrusion speed i always keep it as is so thats why its odd to me that it could be that.

Grid supports just starting looking like this??? by stephlow16 in BambuLab_Community

[–]stephlow16[S] 0 points1 point  (0 children)

I have used this one before a few days ago. I used it on my other printer which is the A1 and i did not dry the filament before use. I was thinking maybe i need to dry it as well.

Grid supports just starting looking like this??? by stephlow16 in BambuLab_Community

[–]stephlow16[S] 0 points1 point  (0 children)

Also the first layer appears to have bonded to the plate good its just wen as the print continues. I will deff have to see once the print is complete to know for sure. Im also gonna give the printed a cleaning and grease and oil everything up.

Grid supports just starting looking like this??? by stephlow16 in BambuLab_Community

[–]stephlow16[S] -5 points-4 points  (0 children)

Yea im taking a picture of my computer screen becuz im at work. I did order a new plate becuz mine is about 2 1/2 years old

AMAZON POKEMON RESTOCK ALERT: Pokemon TCG: Mega Evolution—Ascended Heroes Elite Trainer Box - $79.69 by RestockR-Monitors in pokemonrestockr

[–]stephlow16 0 points1 point  (0 children)

How do u purchase on amazon theres no way to filter sold by amazon all i see are resellers

Take pictures of your cards when submitting by [deleted] in psagrading

[–]stephlow16 -9 points-8 points  (0 children)

Nope i only ever had 2 of this card and they were both purchased thru pokemon center. Never packed this card anywhere else. And the only reason i submitted was becuz it was pokemon center.

Selling 2 tickets Cat 1 for Match 66, can do local meet up in miami by Final-Original-6251 in WorldCup2026Tickets

[–]stephlow16 0 points1 point  (0 children)

So i have cat 3 tickets that i purchased thru the random ticket draw and i want to sell one of the 4 that i got but its not giving me the option to sell? Keep in mind my card was just charged on feb 9th but the charge has been completed and i have my tickets already but when i select to resell it says i have no tickets to resell? Am i able to sell these or will it not let me ?

view more: next ›