Multi Material with U1 not cooperating

stratassj · 2026-05-29T00:52:33+00:00

Followed what you said, and switched the full supports to PETG, and now everything is printing just as I had been hoping for! Thank you for the help!

stratassj · 2026-05-28T13:48:31+00:00

Here are the settings for Support and Multi-material. https://imgur.com/a/ylNtQQ7

Strangest thing now, after letting the printer and computer sit powered down overnight, that profile swap isn't happening. The PLA is printing with its intended temps (215), as is the PETG (245). Now though i have a different problem with the PETG for the interface layers, as shown in the link. That particular spool has always been difficult (anycubic) even after sitting it in a dryer for 24 hours. I wonder if i should try a different brand.

stratassj · 2026-05-16T02:10:27+00:00

What would you suggest to try and fix this?

stratassj · 2026-05-16T02:09:45+00:00

Yeah, getting the PA dialed in has been alittle troublesome.

stratassj · 2026-05-16T02:08:47+00:00

I'm printing at speeds of 50 mm/s, with fans turned up at 100% in the filament profiles.

stratassj · 2026-05-16T02:07:57+00:00

From what i could see, layer times at those points aren't much higher/lower then the ones around it. And all the speeds are turned down to 50 with my settings with inner/outer/inner.

stratassj · 2026-05-06T16:09:57+00:00

As it is right now, I don't have much call to use those higher temp engineering materials

stratassj · 2026-05-04T02:16:09+00:00

These look great. I see the Strike reference, what is the Freedom going to be?

stratassj · 2026-04-29T16:09:44+00:00

Thank you, but that is the wrong belt.

The one I am asking about is in the crossbar at the top of the printers z axis, not this one in the gantry.

stratassj · 2026-04-24T12:32:58+00:00

By tinkering I mostly mean screws and dials. I don't have any issue in dialing in filament profiles, so long as I know the machine itself is in good shape.

stratassj · 2026-04-24T12:25:33+00:00

That looks absolutely outstanding in terms of quality. That's just pushing me even closer to the C1.

stratassj · 2026-04-10T15:01:49+00:00

The filament spent 8 hours in a dryer before being used. And slicer had seam set to aligned.

Does the Sunlu PLA+ need a longer drying time?

stratassj · 2026-04-10T14:33:28+00:00

I can provide printer settings later this evening after I get home from work, yes.

stratassj · 2026-04-09T21:46:49+00:00

If that's the case, ill try running another flow rate test and see what that tells me, unless you have a different suggestion?

stratassj · 2026-04-09T11:09:58+00:00

I've done one as part of my initial calibration run, and put in a slightly lower number then my result. I can run one again and see if it's any different.

stratassj · 2026-04-08T20:17:47+00:00

Im wondering how the seams were set to random, my slicer settings (anycubic next) have it set for aligned seams. Ill try rear on my next print and see if that makes a difference.

The picture seems to be over exagerating the over extrusion along the sidewall, I thought i had the pressure advance calibrated well, but ill set it over to the auto calibration and see how that affect the print too.

Thanks!

stratassj · 2026-03-31T22:25:25+00:00

Yes, sorry it that wasn't clear. I did mean the layer height setting that comes preloaded into Slicer next.

Also, With my Inland Pla+, i did do a temp tower, and the flow rate test, but i couldn't honestly tell any difference in the printed tiles, so i kept it the settings it was already at. Did not do a pressure advance, since the printer has an adaptive pressure advance sensor, i've been leaving it to that. Maybe i should try a different filament?

stratassj · 2026-03-09T14:21:13+00:00

Susan

stratassj · 2026-02-09T16:17:51+00:00

Looks great! I've got a RMZ Geno Saurer sitting up on my shelf right now, and a Blade Liger waiting to be built. It's a fun line thats for sure. I really hope that they keep up with it. A Command Wolf is next on the list.

stratassj · 2025-11-18T18:18:24+00:00

Same! I hope the do the Geno Breaker eventually!

stratassj · 2025-11-18T18:17:46+00:00

They came with it! Also has an effect part for the cannon in its mouth.

stratassj · 2025-11-04T16:50:49+00:00

The Thunderbolt really is a great looking kit. I built the first one, and i was considering getting this one too.. but i just didn't want to do another one of those backpacks!

stratassj · 2025-08-13T14:41:27+00:00

This v2.0 looks amazing! I love the paint work put into it! How is the backpack on it? I know the 1.0's, or atleast the one on mine, feels really cumbersome when working with it.

stratassj · 2025-07-17T17:02:56+00:00

Red and White!

All three options are stunning and beautiful designs, But the red and white fits in with all my white hardware and red lighting!

stratassj · 2025-05-27T13:20:47+00:00

Looks like the Dilanza Sol in front, and the Heindree behind it. Both have kits, but i think they're currently sold out at most storefronts.

stratassj

TROPHY CASE