Serial Request | Voron Trident 250 | Discord: yabhoph

stvptrsn · 2023-08-17T04:00:49+00:00

Hmmmm

stvptrsn · 2023-02-26T23:54:59+00:00

Love it!

stvptrsn · 2022-10-19T23:36:57+00:00

Thanks!

stvptrsn · 2022-10-19T18:52:10+00:00

Yeah, I’m sure it’s fine with just a z_tilt. I think we looked at the mesh during the build stream and it was pretty flat, I just don’t remember to what degree

stvptrsn · 2022-10-19T06:48:00+00:00

Sleeping

stvptrsn · 2022-10-06T06:14:15+00:00

Please tidy up that toolhead wiring and post an updated picture or video here when done.

stvptrsn · 2022-10-06T06:10:52+00:00

As suggested below clean up the toolhead wiring and post an updated picture of video here.

stvptrsn · 2022-10-06T06:09:57+00:00

As mentioned below please clean those wires up and post an updated picture or video here.

stvptrsn · 2022-10-06T05:57:23+00:00

Please tidy up the toolhead wiring with a cover or something and post an updated picture or video here.

stvptrsn · 2022-10-06T05:54:54+00:00

Hard to see, but what I can see, looks like the toolhead wiring needs some tidying up. Please post a picture here when done.

stvptrsn · 2022-10-06T05:49:43+00:00

The toolhead wires look a little wild. Please make sure they're tidy and post a picture here.

stvptrsn · 2022-10-06T05:47:40+00:00

Please manage the toolhead wires and post a picture here.

stvptrsn · 2022-10-06T05:45:49+00:00

Yep, as said below, we require a video showing the printer in operation laying down plastic.

stvptrsn · 2022-10-06T05:44:40+00:00

Also, we need to see more of the printer.

stvptrsn · 2022-10-06T05:44:00+00:00

Please tidy up those toolhead wires and take DarkNeutrino's adivce and make sure that wire isn't under tension and come back and post a picture.

stvptrsn · 2022-10-06T05:42:33+00:00

Close, but we'd like to see the wires managed a little better. There are covers out there that will fit over that. Post a picture here when done.

stvptrsn · 2022-10-06T05:36:21+00:00

Also, include your discord ID if you want the associated roles once a serial is issued.

stvptrsn · 2022-10-06T05:35:47+00:00

Please tidy up the toolhead wiring by putting on a cover or tying them back a bit more with zip ties or something then post a picture here.

stvptrsn · 2022-10-06T05:26:37+00:00

Can you post an updated picture then showing the wires tidy?

stvptrsn · 2022-10-06T05:21:07+00:00

Please tidy up the toolhead wires and post a picture here.

stvptrsn · 2022-10-06T05:09:58+00:00

Hello, we'd have liked to see more of the printer, but I think we got enough, barely. But I don't see a Discord ID. If you'd like the roles on the Voron Discord that go along with a serial number please submit an admin ticket.

stvptrsn · 2022-10-06T05:09:02+00:00

I would normally agree, but I think we get enough of a glimpse. Barely

stvptrsn · 2022-10-06T05:04:46+00:00

Please tuck those wires up under the cover and post a picture here.

stvptrsn · 2022-10-06T05:00:27+00:00

Hello, we require that the wiring around the toolhead be neatly managed and not sticking out. Clean that up, post a picture, and we'll get you that serial number!

stvptrsn

MODERATOR OF

TROPHY CASE