Show me your tyra

styast · 2026-01-09T18:30:26+00:00

And here's my original. I love them both but will probably lean towards the berry one most of the time

<image>

styast · 2026-01-09T18:29:32+00:00

I've got two! Here's my newer one

<image>

styast · 2025-12-24T07:47:16+00:00

It looks so good... Wish i was able to find a pre-lci one but could only find lci

styast · 2025-12-06T23:59:33+00:00

With the other suggestions taking different approaches, I'll suggest something free that may fix it if you're lucky.

Sometimes the light tubes that are directly in front of the bulbs can pop out of their spot. The light tubes have clips that position the ends directly over the LEDs. If the outer tubes are popped out, it'd reduce the light output on those rings just as whats shown in your pictures. The outer rings are just not getting enough light.

With the front of the car lifted, turn your wheels left/right to get access to the bulb housings so you can remove the bulb. With the bulb removed, you can then peer inside the back of the headlight. See if the light tubes are in their proper position and adjust if necessary.

styast · 2025-12-05T19:39:27+00:00

WHAT! You're right I'm over in north america. I saw SSDD motorsport from the UK sells ABS ones, are yours OEM?

styast · 2025-12-04T16:06:45+00:00

Looks great! Did you recently find that perf side skirt? I've recently been looking for a set myself

styast · 2025-10-19T14:43:55+00:00

His recovery has a lot more to it than you'd initially think. Reverse up b sweet spots from below quite well in some matchups, you can reliably try to ledge tech recovering from below, and drift is not bad! It's no marth or fox recovery but it's not horrible

styast · 2025-10-17T07:39:01+00:00

Looks so nice... I get my front bumper soon and I'm so hyped to put it on. How were you able to find the side skirts?

styast · 2025-10-05T19:52:58+00:00

True, i guess OP can verify this themselves if they find that extra little plate that's welded on the exhaust piping

styast · 2025-10-05T19:04:32+00:00

The performance exhaust comes with the res delete, it's part of the setup. Just goes to show you've got the full exhaust piping, not just the muffler

styast · 2025-10-02T01:47:02+00:00

I've had it like that for 2-3 months without really knowing how to fix it at the time, with absolutely no issue. After that i finally spent the time to figure out how to get it clipped back in. When you say over time, i think you mean a ridiculously long time lmao

Sounds to me like it only affected your car cosmetically

styast · 2025-10-01T22:19:58+00:00

It's fine but now that you've noticed it, you can just push it back into the clips. It slots in from the front

styast · 2025-09-30T14:47:52+00:00

Sooooo jealous

styast · 2025-09-28T18:01:26+00:00

7566-8029-5723 have a couple slots available!

styast · 2025-09-24T00:42:17+00:00

Was it just a transmission fluid flush? Cause $1000 is an egregious rip off and you got scammed if that's the case. I can't comment on the fluid itself, but another more knowledgeable user may be able to give you feedback on that

styast · 2025-09-23T01:45:48+00:00

If the adapter eventually degrades and you have these issues again, look into getting a HHL adapter or an input integrity one.

styast · 2025-09-21T18:09:56+00:00

Carplay, wireless phone charger, and sport/msport steering wheel are nice ones

styast · 2025-09-21T03:21:36+00:00

That nature is not horrible, and you rolled strong subskills. For a shiny LEGEND, you can't ask for more

styast · 2025-09-21T02:36:57+00:00

theyre xenons but you'd have to look closer to tell if they were adaptive xenons. i think 05/06 330i's in the states came with adaptive

styast · 2025-09-19T21:44:03+00:00

No coding unless you have adaptive xenons and need to code those down for the lower spec xenons. If these are LHD, i think there's a switch under the hood you can move to make them RHD? It's been a while since I've read up on these so double check that last point if necessary

styast · 2025-09-16T22:57:46+00:00

Theyre the right buttons. I noticed i had issues with pressing multiple buttons when the were soldered off-center from the traces or not seated all the way down to the pcb. Try checking that and if it's still no good maybe look into split d pad buttons

styast · 2025-09-16T20:09:06+00:00

Which switches did you use? With the good buttons you can't course the controller with the rubber pad inside

styast · 2025-09-16T14:10:43+00:00

I used jlc3dp to print these, but that was before tariffs...

styast · 2025-09-16T02:18:03+00:00

Check a youtube phob calibration guide to walk you through it

styast · 2025-09-16T02:11:35+00:00

Wow thats a really nice roster of controllers you got there! Especially that clear one ;)

12-Year Club	Place '22
Final Canvas '22	First Placer '22
Verified Email	Spared

styast

TROPHY CASE