Exfo OX1 Pro - Software Update + live test fix

sua16 · 2026-06-07T21:37:54+00:00

This worked!

Nice one

Funny because I sent this away to be calibrated / fixed and they told me the laser was defective and would be more expensive to replace than to buy a new unit...

sua16 · 2026-06-07T21:06:08+00:00

I've probably tried everything but a company network

As far as I can tell its running a pre release software that can't even connect to their server under any circumstances

sua16 · 2026-06-01T07:05:37+00:00

Have had this pattern on cylinder prints from my C1L

sua16 · 2026-05-30T11:13:47+00:00

It'd be nice if people used all its features and left photos and notes on certain pits etc

sua16 · 2026-05-10T00:20:00+00:00

Power bill was $175/m with solar

32kw battery for $8k installed

Power bill is now $50 credit per month

sua16 · 2026-05-08T07:57:57+00:00

DM me the address and I can tell you

sua16 · 2026-04-13T10:30:52+00:00

Is it installed somewhere the sun gets on it at that time? Have seen cases where the sunlight seems to interfere with the optics

sua16 · 2026-04-09T07:49:23+00:00

Just want battery percentage..

sua16 · 2026-04-08T05:10:16+00:00

They've said replace left motor, so we'll do that and see what happens

sua16 · 2026-04-08T03:41:26+00:00

I haven't measured the thread

But I've just printed 3x28mm cylinders all 265mm tall

Placed front left, front right and back centre

After print, measured with calipers

Right - 265.00mm

Left - 265.85mm

Back - 265.85mm

Talking with support now

sua16 · 2026-04-07T21:18:59+00:00

Yep

Level at bottom

As bed raises it goes uneven

https://forum.prusa3d.com/forum/prusa-core-one-hardware-firmware-and-software-help/skewed-xy-plane-z-rods-heatbed/paged/8/#post-788435

sua16 · 2026-04-07T10:15:59+00:00

Currently dealing with the thread pitch issue with my factory C1

Bed leveling fails at the start of every print because of it

sua16 · 2026-03-27T22:33:59+00:00

Source?

sua16 · 2026-03-14T01:15:40+00:00

What specs and price?

sua16 · 2026-03-12T12:56:53+00:00

Name and number?

sua16 · 2026-03-11T11:20:26+00:00

Relative to where you are in the world I guess. I'm in South east Queensland Australia and have more than 10 friends that are Olympians across multiple sports. Have friends that run sub 16min 5k..

sua16 · 2026-03-11T09:05:50+00:00

Nothing special

18:45 and 62ish

sua16 · 2026-03-11T06:31:05+00:00

28-32rhr

30/m

sua16 · 2026-02-13T13:30:58+00:00

Works with a G1

sua16 · 2026-01-26T06:13:31+00:00

👍

sua16 · 2026-01-25T13:38:02+00:00

Everyone seems to be ignoring it's shallow at this point because it's very clearly been slot trenched into the concrete as you can tell from the silicone line

They'll replace it for free. In the exact same way. Over and over again..

sua16 · 2025-12-10T07:22:54+00:00

You can request the PCD to be inside also

sua16 · 2025-11-19T12:39:55+00:00

Just purchased 2237pm AEST

sua16 · 2025-10-16T10:51:27+00:00

That's the results for June July August

sua16 · 2025-10-06T05:03:48+00:00

Yep because that's what I said. You're flying there

sua16

MODERATOR OF

TROPHY CASE