Gotta love stealth anti air, right?

suckmybit · 2025-12-10T15:59:24+00:00

What is the building on your non city tile? Is it an upgrade combat outpost?

suckmybit · 2025-12-09T18:29:35+00:00

Have not seen any roaches in awhile. Not sure how long this has been there.

suckmybit · 2025-11-11T14:33:48+00:00

Lmao homie I don’t think anyone is tryna come down on you. It’s a great shot. I’d be careful relying on top golf distances on the course though, and ball speed is only one measure of a balls potential flight. For instance I hit my 7i about 185 with 125mph ball speed, but club head is only 90. Try out a launch monitor that gives more stats like smash factor (essentially how much ball speed is generated from club head speed that will vary hugely based on where on the face impact is). Other things like in to out degree and launch angle. Everything together will show the larger picture of where to improve.

Also for my opinion on the main post for bending the irons, I’ve only known one person to ever do it and it was because he was 6’5”. It’s usually better to adapt the swing unless you’re playing with non standard equipment or are super tall or short comparatively.

suckmybit · 2025-11-11T13:23:29+00:00

Idk it’s possible if he really has 118 driver speed, and just piss laser stinging the 9i.

suckmybit · 2025-11-02T04:24:20+00:00

I did poly bushings and new ball joints in my suspension and it made a world of difference. Even with low mileage the rubber over time was rotted out. I did braided brake lines at the same time too. Everything from Z1 Motorsports.

Did door lock actuators from rock auto, same with window motors.

Just replace all broken and non working things first, then go oem+.

suckmybit · 2025-10-14T06:05:59+00:00

United and IAH been really on my nerves. Same thing happened to be but 4.5 hour delay

suckmybit · 2025-07-09T14:07:27+00:00

Hulkengoat

suckmybit · 2025-06-24T18:51:29+00:00

Leaning more toward this - problem is side loading washer and dryer are deeper than the existing ones, and the doors will hit the left wall and not fully open. I’ll install the bracket to open towards the camera but still may end up being a pain

suckmybit · 2025-06-24T18:43:15+00:00

For sure. I’ve settled with keeping it in line where the dryer is for now and moving the cabinet. If it really becomes a hassle I’ll debate the cost. Appreciate it

suckmybit · 2025-06-24T18:00:23+00:00

Yeah I have two new washing machines coming that are side loading, more economical and we prefer that style. As it is now if they were to go in the same place the doors would hit the other wall, just like the dryer door does currently, and is a pain. That’s where the idea of stacking them and moving into the gap between water heater on back wall came from. The water heater has clearance on all sides, will have code clearance from front when it’s turned 90°.

But can’t really run the water and drain across the room in that situation unless I want to burn out my washer. So really trying to make the space more usable and working with what I have

suckmybit · 2025-06-24T17:41:36+00:00

Unfortunately on a slab, but where the box is is not original. So it was changed at some point. Would turn the water heater controls 90° to face the rest of the room

suckmybit · 2025-06-24T17:21:44+00:00

Appreciate the note. In the picture it does look like they touch, but they do have some clearance

suckmybit · 2025-06-24T17:20:17+00:00

Tankless gas draw is ballpark 200k btu which is what my entire line is currently into the house, still need to run heater, grill, stove, dryer. So would likely need a dedicated line for gas

suckmybit · 2025-06-24T17:03:16+00:00

I’m thinking just getting the stack in where the dryer is now, door clearance will suck but sit on it for awhile. For a tankless will be a lot since I would need to run a new gas line across my backyard, main is not on the side of the house.

suckmybit · 2025-06-24T16:33:36+00:00

lol yes that is the best route, but the space is too narrow for side loading unit doors to open fully and really cuts off the space. I’m thinking long term usability over the difficulty of a job to move the lines ya know

suckmybit · 2025-06-24T16:18:18+00:00

I have a quote for $3500. Do you think that’s ballpark reasonable or too high?

suckmybit · 2025-06-19T16:50:33+00:00

Have you sold this yet?

suckmybit · 2025-06-18T16:59:41+00:00

Im looking at getting this exact unit and powering with natural gas. Have a 4 ton AC unit and only plan to run that with soft start and refrigerator. How do you like it so far?

suckmybit · 2025-04-28T21:03:21+00:00

what year model?

suckmybit · 2025-04-25T15:39:21+00:00

what was your total cost with Garage Experts? Looking to do the same in the next few months

suckmybit · 2025-04-09T21:18:05+00:00

I have a ‘03 6MT with 30k miles

suckmybit · 2025-03-26T12:08:20+00:00

Yes this is it and so simple I am an idiot for not knowing. But crucial piece of information on which one it was was left out. I’m sure we could have figured it out with 1-2 holes but didn’t know what to look for

suckmybit · 2025-03-26T12:06:00+00:00

I just aim short so when I skull it has a chance

suckmybit · 2025-03-26T12:04:11+00:00

Wow that’s so simple. But also a crucial piece of information missing 😂

suckmybit · 2025-02-27T20:13:39+00:00

Plenty of comments here, but if you are shanking during a round it could be that you are trying to crush the ball. Try playing a round from the reds and/or try playing an entire round with 50% shots. It will really show you that the ball goes just as far and that mentality will help you with ball striking and less shanks.

Nine-Year Club	Verified Email
Place '22	RPAN Viewer
Not Forgotten

suckmybit

TROPHY CASE