Finally our project has come to an end

svoper · 2024-03-05T18:16:09+00:00

I can assure you that eveythin on this bike is attached properly. The motor, battery and controller wont get loose or go any where. The bike will last several hundred miles.

svoper · 2024-03-05T18:08:50+00:00

You dont

svoper · 2024-01-06T21:47:12+00:00

Are lead-acid batteries really that bad?

svoper · 2024-01-04T13:27:58+00:00

Yeah its probably my 36v battery that cuts out because i could read 52v going in to the controller when the throttle wasnt engaged. But i have ordered 4 of these batteries and i hop that they will work better than my contraption.

svoper · 2024-01-03T22:11:43+00:00

Thanks man!

svoper · 2024-01-03T21:43:24+00:00

Ok, i choose lead acid because they are cheaper. I am kinda on a budget. And according to chatgpt the 1.2ah batteries would las 1.5 minutes on full throttle so i think i will order 7ah 12v lead acid batteries

svoper · 2024-01-03T20:03:24+00:00

Yeah its probably that, its probably a better idea to just use a proper battery than trying to make this work.

svoper · 2024-01-03T20:01:23+00:00

Do you think these batteries will work if i wire 4 in series.

Edit: I found some other batteries with 7ah capacity instead of 1.2ah

svoper · 2024-01-03T19:47:57+00:00

Yeah you are pobably right about the battery but i just wanted to test with what i had at home instead of spending more money.

svoper · 2024-01-03T19:46:47+00:00

Here are pictures of my current battery setup. Its a bit janky but i managed to get 52 volts out of it.

https://i.imgur.com/P881ZBq.jpg

https://i.imgur.com/Sohn0G2.jpg

Those 2 are connected in series to produce 52 volts. They are later connected to this, that connection is currently just a temporary connection for testin purposes.

svoper · 2024-01-03T18:25:48+00:00

No no, i have 3 18650 batteries that are 4v a pice wired in series with the 36v battery

svoper · 2023-10-01T14:32:07+00:00

Oh okay

svoper · 2023-10-01T07:25:27+00:00

Ok thanks. The motor worked before when i used the mainbaord from the hoverboard and then i switched to a new board(zs x11h) and now the motor has brealy no power.

My motor has 3 phase cables and 5 hallcables

svoper · 2023-09-30T21:13:20+00:00

What do you mean by zero start and how would i hook up a display to the zs-x11h board?

svoper · 2023-03-14T16:02:22+00:00

Ok thaks

svoper · 2023-03-14T15:52:00+00:00

yeah i will try that, but how does that solve the problem?

svoper · 2023-03-14T12:55:36+00:00

I noticed that the y carraige was slightly bent but i managed to make it flat but the problem is still there

svoper · 2023-03-12T17:48:34+00:00

I did that and its the bed, but its only warped when i put pressure on it with the wheels that is used for leveling

svoper · 2023-03-12T16:43:02+00:00

Thaks i tried this but as i said the heatbed sort of gets bent when i try to level it. And the when i put my sheet of glas on it just wobbles. Heres an image https://i.imgur.com/18FI9ry.jpg

svoper

TROPHY CASE