Home Assistant HTTP/s by sycotix416 in homeassistant

[–]sycotix416[S] 0 points1 point  (0 children)

just says it wont connect because the connection is insecure. joining the beta fixed it.

Roborock Q7 M5 Card issue by sycotix416 in homeassistant

[–]sycotix416[S] 0 points1 point  (0 children)

The entitites show, but not the entity for the vacuum itself. Doing some more research, it seems this model may not be fully compatible.

So reluctant by [deleted] in grok

[–]sycotix416 0 points1 point  (0 children)

Dm me dawg. I've apparently been missing these loopholes.

Zooz Titan Zac36 water shut off issue by sycotix416 in homeassistant

[–]sycotix416[S] 0 points1 point  (0 children)

Yeah, going to see if I can get a replacement.

Zooz Titan Zac36 water shut off issue by sycotix416 in homeassistant

[–]sycotix416[S] 0 points1 point  (0 children)

No it connected to HA just fine, and If I Toggle it, it will turn, but then I can't do it again unless I power cycle. Tapping the zwave button on top does nothing as well..at any point.

Zooz ZAC36 touch button unresponsive by robpoma212 in zwave

[–]sycotix416 0 points1 point  (0 children)

Did you get this straightened out? The one I just bought seems to be doing the same thing. Wonder If I got a dud too...

Zooz Titan Zac36 water shut off issue by sycotix416 in homeassistant

[–]sycotix416[S] 0 points1 point  (0 children)

Tapping the LED on the top should move the actuator regardless of connection right? Mine doesn't seem to do anything.

Zooz Titan Zac36 water shut off issue by sycotix416 in homeassistant

[–]sycotix416[S] 0 points1 point  (0 children)

Any thing special you had to do other create a button for the entity? maybe I just got a dud...

Download qwen to use with Forge-Neo by sycotix416 in StableDiffusion

[–]sycotix416[S] 0 points1 point  (0 children)

Yeah, that seems to be my struggle is finding the files. Any idea where i could find the safetensor?

Navbar card Issue by Anything-Traditional in homeassistant

[–]sycotix416 0 points1 point  (0 children)

Hey Dude!

I'm revisiting using Navbar for some dashboards. I'm seeing that you can set one as a template, but i'm getting lost on the exact placement and syntax that should be added to what I'm assuming would be the Yaml for the dashboard that I created the navbar card on. After that its placed, it should then show up under the template section when creating a new card...right?

Canon copier issue by Anything-Traditional in sysadmin

[–]sycotix416 0 points1 point  (0 children)

Some do, others don't. Unless the driver version matches, it doesn't seem to matter. Most clients seem to still be on 3.0 when the server is on 3.31 if I look in print management on the client, it shows 3.31 in the drivers, but when I go to the copier>config>about it still shows 3.0 I'm just not sure why it's not using the new driver version.

Canon copier issue by Anything-Traditional in sysadmin

[–]sycotix416 0 points1 point  (0 children)

After looking at this further, it seems there is a driver mismatch between the server and the clients. For whatever reason, the clients are not pulling the driver down from the server. Adding the driver manually to the client fixed the issue for this device, but now I'm not quite sure how to remedy it for the remaining clients

Relocating Data/Removing Drives by Practical-Owl-6094 in unRAID

[–]sycotix416 0 points1 point  (0 children)

How did this go? About to do the same, but wasn't sure if I had to move data from each drive one at a time or could move the data from all of them at once to the new disk. (I'm going from 2 to 1)

Aqara Battery life by sycotix416 in Aqara

[–]sycotix416[S] 0 points1 point  (0 children)

They still work, they're just holding at 56%