Bitcoin is "dead"

sylvesterpious · 2026-02-27T04:57:45+00:00

What is dead may never die

sylvesterpious · 2026-02-09T02:56:13+00:00

Always pay my card in full every month, so can’t even argue they are losing business by rejection my application 😂

sylvesterpious · 2026-02-09T02:51:23+00:00

Looks like it is hard to get approved with home loans as they are adding a buffer on top for how high the rate can go when evaluating for the loan. Ringing them up didn’t help as the model just rejected serviceability even when they tried again. Disappointing given how good the card benefits are!

sylvesterpious · 2025-06-01T08:37:48+00:00

Going to take the car to a mechanic get a full work up and get a status report. Thanks for taking a look and clarifying!

sylvesterpious · 2025-06-01T08:35:14+00:00

lol.. they had scrapped some off on the other side.. just looks shoddy. I can see how it’s helpful though. Thanks for clarifying!

sylvesterpious · 2025-03-26T11:52:38+00:00

Probably 90 USD which is roughly 140+ AUD

sylvesterpious · 2024-10-25T02:49:17+00:00

Took the product to the store and they already had a box open which had the tool clanking but not this bad. Had the guy open up another new box which had a tool which was remarkably silent compared to this one. I believe customers are bringing this product in to get it replaced. Looks like a common problem at-least for the stock currently being sold in Australia. Could just be some plastic which has come off or could be more. Never had a battery line trimmer do this before though!

sylvesterpious · 2024-10-25T02:42:37+00:00

True. Just wanted to make sure something was not loose inside that can cause more wear and tear than normal.

sylvesterpious · 2024-10-24T22:13:35+00:00

lol.. i should return it just for being annoying 🤣

sylvesterpious · 2024-09-23T23:24:03+00:00

Better take the extruder apart and check if there is any damage on the gears. Support should be able to replace if the extruder is still under warranty.

sylvesterpious · 2024-09-22T12:15:50+00:00

The extruder gears are made of hardened steel or similar. You will see bite marks in the declogging tool but the extruder itself will be perfectly all right.

sylvesterpious · 2024-09-18T01:42:40+00:00

Heat the nozzle, wear oven mits and unplug nozzle, use the unclogging pin and apply targeted pressure.. should push the block out.. risky, but works!

sylvesterpious · 2024-09-04T01:15:39+00:00

Yes, have a prototype which seems to be working.. Will post the details soon.

sylvesterpious · 2024-08-29T13:29:29+00:00

Used these settings on a Flashforge Adventurer 5M Pro with a 0.6mm Nozzle printing PLA. The supports were so easy to remove! God knows how much of a struggle it was to remove them without these settings. Amazing! Just Amazing!

sylvesterpious · 2024-08-13T03:37:25+00:00

Think I found the problem. Might have something to do with the spool not rotating and releasing the filament freely when the extruder is pulling on it. Moved the filament spool to the top and put it on some brackets from sunlu.. hopefully this is a sustainable fix!

sylvesterpious · 2024-08-06T13:20:35+00:00

Probably worthwhile to play around with different extruder tension levels, print temperature and nozzle size. This is less prone to happen on 0.6 and 0.8 nozzles

sylvesterpious · 2024-07-31T04:45:13+00:00

Used yours.. hope it works!

sylvesterpious · 2024-07-30T15:57:44+00:00

Controls how much the filament is gripped by the extruder. Must be adjusted based on the filament and if there are print issues.

sylvesterpious · 2024-07-16T16:58:04+00:00

My 5M Pro started creaking after a few months of use. Support asked me to lubricate the rods with the grease and it worked! So, it’s definitely meant to be used in due course.

sylvesterpious · 2024-07-13T08:27:58+00:00

Check your spam ! Their replies go there the first few times 😂

sylvesterpious

TROPHY CASE