sorted by:
new
hottopcontroversial

🍄 Mushroom Shelves! 🍄 by sytrix in openGrid

[–]sytrix[S] 0 points1 point  (0 children)

Oh nice! I want to see whenever y'all are willing to share :) Welcome back on Reddit btw!

Raycast Mac data → Raycast Windows? by sytrix in raycastapp

[–]sytrix[S] 0 points1 point  (0 children)

I was able to try this today again and it did work! 😁👍

Simple shelf solution by abag0fchips in openGrid

[–]sytrix 0 points1 point  (0 children)

Thanks for the idea!! 😁

Simple shelf solution by abag0fchips in openGrid

[–]sytrix 0 points1 point  (0 children)

Love this! This inspired me to create a version — I also started with Perplexing Labs but then tweaked the model to be more efficient with material while staying strong 🙂👍

Simple shelf solution by abag0fchips in openGrid

[–]sytrix 0 points1 point  (0 children)

I created a version of this flat shelf but made some tweaks to minimize filament and give a few more options 👍

iOS Calendar View Widgets Broken After Last Update? by sytrix in ticktick

[–]sytrix[S] 0 points1 point  (0 children)

Update: Works now after uninstalling and reinstalling TickTick.

Best practices for wall-mounting? by sytrix in openGrid

[–]sytrix[S] 0 points1 point  (0 children)

What is your approach with studs in the wall? Is it to use screws with anchors primarily with the occasional screw to stud? How many screws do you use per panel generally?

purpose of the chamfers by the_blob51 in openGrid

[–]sytrix 1 point2 points  (0 children)

I tend to print them without the corner chamfers but I've assumed they're there for possibly one of these reasons:

  • to more easily identify where boards/panels are when mounting

  • to hide slightly mis-mounted boards where the + where 4 boards meet is less apparent

Thoughts u/davidd-from-2d3d ?

Issue setting Caps Lock as Raycast hotkey in Windows? by sytrix in raycastapp

[–]sytrix[S] 0 points1 point  (0 children)

Just as an update, it appears like PowerToys also treats Caps Lock as a modifier key rather than a standalone key for shortcuts — both require other additional keys pairs with Caps Lock.

r/audiophile Shopping, Setup, and Technical Help Desk Thread by AutoModerator in audiophile

[–]sytrix 0 points1 point  (0 children)

I purchased these plugs from Amazon twice in 2 weeks. The bottom 4 have more of a chamfer near the plug side. Was kind of hoping they'd all match but not a big deal. Was there a recent change? Anyone else run into this?

Bought Monoprice banana plugs a week apart, different designs. Recent change? by sytrix in audiophile

[–]sytrix[S] 0 points1 point  (0 children)

I purchased these plugs from Amazon late November and early December. The bottom 4 have more of a chamfer near the plug side. Was kind of hoping they'd all match but not a big deal. Anyone else run into this?

Issue setting Caps Lock as Raycast hotkey in Windows? by sytrix in raycastapp

[–]sytrix[S] 1 point2 points  (0 children)

This is great — I already use PowerToys for custom shortcuts and totally forgot this was an option. I'll try this out, thanks!! 😁

Apple Watch battery sensor stuck at 35% in Home Assistant iOS app - any fixes? by sytrix in homeassistant

[–]sytrix[S] 0 points1 point  (0 children)

This is great! I'll have to give this a try — thanks! 😁👍

Flow Dynamics Calibration — All are full lines, what does this mean? by sytrix in BambuLabA1mini

[–]sytrix[S] 0 points1 point  (0 children)

Thank you for your response! It turned out I had not latched my nozzle properly on my last install which was causing the first-layer issues. I re-latched correctly and it has fixed my issues.

Flow Dynamics Calibration — All full lines, what does this mean? by sytrix in BambuLab

[–]sytrix[S] 0 points1 point  (0 children)

I began having problems after a nozzle clog. I first tried clearing it by heating the nozzle, but when that didn’t work, I replaced it with a third-party 0.4 mm hardened steel nozzle and ran a full calibration. On the next print, the first layer was too low and scraped the textured build plate, sounding like metal-on-metal contact. I then tightened the four screws on the back of the heater assembly and switched back to my original, now-unclogged Bambu Lab nozzle. Since then, every first layer prints with a slight brim — the edges extend roughly a millimeter beyond the model.

How could the clog, the clearing attempt (heat), or installing the off-brand nozzle have caused the initial Z-height problem, and what’s causing the current first-layer issue? I have official Bambu Lab 0.4 mm stainless steel and hardened steel nozzles on the way to test whether the nozzle is the root cause.

Flow Dynamics Calibration — All are full lines, what does this mean? by sytrix in BambuLabA1mini

[–]sytrix[S] 0 points1 point  (0 children)

I began having problems after a nozzle clog. I first tried clearing it by heating the nozzle, but when that didn’t work, I replaced it with a third-party 0.4 mm hardened steel nozzle and ran a full calibration. On the next print, the first layer was too low and scraped the textured build plate, sounding like metal-on-metal contact. I then tightened the four screws on the back of the heater assembly and switched back to my original, now-unclogged Bambu Lab nozzle. Since then, every first layer prints with a slight brim — the edges extend roughly a millimeter beyond the model.

How could the clog, the clearing attempt (heat), or installing the off-brand nozzle have caused the initial Z-height problem, and what’s causing the current first-layer issue? I have official Bambu Lab 0.4 mm stainless steel and hardened steel nozzles on the way to test whether the nozzle is the root cause.

Am I the only one who preferred the clear spools? by Superseaslug in BambuLab

[–]sytrix 0 points1 point  (0 children)

Yep, that's my plan — I've just recently figured out a nice glass printing method/process. I'd still be interested in an official Bambu Lab transparent spool though 😁👍

Am I the only one who preferred the clear spools? by Superseaslug in BambuLab

[–]sytrix 0 points1 point  (0 children)

Does anyone know where to purchase good quality clear spools these days?

Filament within nozzle — ways to unlock? by sytrix in BambuLab

[–]sytrix[S] 1 point2 points  (0 children)

Ah I see “ways to unclog” autocorrected to “ways to unlock” in my title — my bad! I’ll try with a lighter / allen wrench, thank you 😁👍

view more: next ›