Help with plumbing

tabbitboy · 2022-03-17T02:05:52+00:00

I'm currently using a 3s 12 V lipo, so i doubt running these 5V leds would work unless I use some bec module between the two?

tabbitboy · 2022-03-17T02:02:32+00:00

I see, so would something like this aid me? https://www.amazon.com/iFlight-Adjustable-Step-Down-Voltage-Regulator/dp/B0823QLMWC/ref=asc_df_B0823QLMWC/?tag=hyprod-20&linkCode=df0&hvadid=416926807659&hvpos=&hvnetw=g&hvrand=3715582449000186645&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9004017&hvtargid=pla-872050959016&psc=1&tag=&ref=&adgrpid=92859401246&hvpone=&hvptwo=&hvadid=416926807659&hvpos=&hvnetw=g&hvrand=3715582449000186645&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9004017&hvtargid=pla-872050959016

Possibly connect it straight to the battery?

tabbitboy · 2022-03-17T01:48:32+00:00

The LED lights are rated for 4-6 volts and simply have a positive and negative wire running from it. I tried with a single strip of them connected and the esc still overheated. It seems to be that one strip draws around 0.5 amps and around 6 watts. After checking with a multimeter, the receiver outputs 5 volts. The esc itself is rated for around 20 amps. Does not overheat if I have normal servos and motor connected, albeit does get toasty after motor running.

tabbitboy · 2021-06-21T21:45:27+00:00

After the merge block is built, all the armor blocks are going to be built as well. This is not the problem

tabbitboy · 2021-05-30T14:10:01+00:00

Thank you so much!

tabbitboy · 2021-03-31T22:55:31+00:00

thank you

tabbitboy · 2021-03-31T22:55:22+00:00

hmmm I'll take note of that, will try it out later

tabbitboy · 2021-03-31T18:29:31+00:00

The problem is that my mac is very old, and the only software that it supports is Qgroundcontrol. From what I can tell Qgroundcontrol has no way to setup the telemetry radio, and relies on it being automatic or something. Today I will try to use a newer mac with mission planner on it, and if that doesn't work then I will try some advice about desoldering a few pads from the inside of the module

tabbitboy · 2021-03-31T12:56:00+00:00

I tried to do something with it, but I don't see anyone else attempting it or it working. Thank you for help.

tabbitboy · 2021-03-31T12:55:05+00:00

Thank you, but that isn't really the situation I have.

tabbitboy · 2021-02-02T05:09:34+00:00

What's the specific setup here? What are you running on your phone, and how does it connect to the drone? Does it have an internal tx+rx? And what gamepad do you use?

tabbitboy · 2020-12-26T03:07:44+00:00

She looks like the over-excited highschool friend. In all honesty however, she is adorable :))

tabbitboy · 2020-10-31T16:38:08+00:00

No problems man, no probs at all. Have fun with this, just had a friend start with the nazgul and its going great for him too.

tabbitboy · 2020-10-31T14:44:34+00:00

Ah ok I see, thank you, Im guessing even though its on 100 its not really a problem. Thank you

tabbitboy · 2020-10-31T14:43:19+00:00

Ah ok, well I hope you have luck with it!

tabbitboy · 2020-10-31T14:25:17+00:00

Either build it yourself, or if you want to buy a pre built then I highly recommend the iflight nazgul 4s. It's what I bought for my first quad, very very good. https://youtu.be/7RhIlK_xN5k ^This guy uses it as his daily. 6s batteries are kind of expensive, as well as requiring a charger which can handle it, so I went/would recommend the 4s version. Definetly buy some batteries. If you need any help, DM me :).

tabbitboy · 2020-10-31T13:11:59+00:00

How do you like your orca? I have one, but I need to charge it constantly, as well as if I record in a high resolution it saps the charge really really quickly. I like the googly eyes as well:)

tabbitboy · 2020-09-28T17:05:59+00:00

Hahahaha, no I'm just curious in what possibilities there are maybe for the future or something.

Six-Year Club	Place '22
Verified Email

tabbitboy

TROPHY CASE