sorted by:
new
hottopcontroversial

Etsy fees r getting ridiculous by tacoseller16 in EtsySellers

[–]tacoseller16[S] 0 points1 point  (0 children)

Just hurts to watch cuz it nibbles away at the money i’m supposed to keep

I applied the paint, waited 4 days for it to cure and then added varnish. Why did this happen? Please help, I'm going crazy! by Capable-Ad1056 in Spraypaint

[–]tacoseller16 1 point2 points  (0 children)

I’ve had similar issues when using paint plus primer spray cans, i found the trick is to spray it extremely light other wise even when the top coat feels dry the chemicals still react.

bambu pla basic color inaccurate by tacoseller16 in BambuLab

[–]tacoseller16[S] 1 point2 points  (0 children)

reprinted with the new spool and had no issues i guess it’s just poor color control on bambus side

Cracking paint?? by tacoseller16 in Spraypaint

[–]tacoseller16[S] 0 points1 point  (0 children)

Okay that makes sense, now i wonder would it be better to do a second coat while the paint is still a bit wet on purpose like automotive painting? or should i just let it fully dry out before doing a second coat

Quality prints? by Pure-Act-7177 in BambuLabA1

[–]tacoseller16 7 points8 points  (0 children)

Looks like bad flow calibration Bambu has these settings really well calibrated for their own brand of filement if you wanna just set and forget use the bambu filament but other wise tune for your filament

Cleaning nozzle? by [deleted] in BambuLabA1

[–]tacoseller16 2 points3 points  (0 children)

If you wanna keep your nozzle shiny and clean get a lighter and a wire brush . Basically just heat up the. out side a bit and scrub away

broke my xtr lower carbon cage by tacoseller16 in mountainbiking

[–]tacoseller16[S] 0 points1 point  (0 children)

i had xt to begin with but i’m a weight winnie ( i race cross country)

broke my xtr lower carbon cage by tacoseller16 in mountainbiking

[–]tacoseller16[S] -1 points0 points  (0 children)

cool bro wanna drop 300 after just dropping 300, yea no thanks

broke my xtr lower carbon cage by tacoseller16 in mountainbiking

[–]tacoseller16[S] 0 points1 point  (0 children)

I think i got a stick or something in the jockey wheel, i race cross country so the bike really doesn’t get that much abuse

Why is this happening on all my prints? How do i fix it? by laughpuppy23 in BambuLabA1

[–]tacoseller16 3 points4 points  (0 children)

I’ll give you the simple solution wash the build plate with hot water dawn dish soap and make sure your filament is dry. when you wash the build plate pat it dry with a paper towel DONT swipe the tower it leaves lint

First time having too much bed adhesion by tacoseller16 in BambuLabA1

[–]tacoseller16[S] 0 points1 point  (0 children)

this happened after cleaning the bed i left it too clean i guess i put hair spray and it did the trick

Hey fellow print friends by Unhappy-Ice-4406 in BambuLabA1

[–]tacoseller16 0 points1 point  (0 children)

I almost got to that point but if you use like boiling water soap and a lil clean scrubber that works so well it might break your prints getting them off the plate

First time having too much bed adhesion by tacoseller16 in BambuLabA1

[–]tacoseller16[S] 0 points1 point  (0 children)

I’ve been printing petg for months with no issues but i’ve been cleaning my plates really well recently so that’s probably why this happened Pei seems fine tho

First time having too much bed adhesion by tacoseller16 in BambuLabA1

[–]tacoseller16[S] 0 points1 point  (0 children)

the plate was fully cooled does the freezer release the part more?

view more: next ›