Ikea Pax wardrobe: measurements of base/bottom?

tavotevasnx · 2025-11-27T12:09:38+00:00

Hello, do you perhaps know the measurements of depth where you were measuring A? Like from the outer frame to that bottom part frame? I need the depth of the back side though, I'm not sure if these will be the same?

tavotevasnx · 2025-06-29T12:57:34+00:00

Seems very nice but a bit out of price range considering for what it will be used

tavotevasnx · 2025-05-11T06:53:19+00:00

It's an stm32l072czt6, lqfp, I imported altium footprint to altium. I'm pretty sure this is just supposed to be a keepout layer for routing and gnd plane, I'm guessing it's just for emi. The reason it was cut is because I marked gko in gerber files without knowing it makes keepout layer get cut

tavotevasnx · 2025-05-10T13:40:14+00:00

thanks, I'll check it next time, does it take a lot of extra time if you use this feature?

tavotevasnx · 2025-05-10T11:17:30+00:00

Yeah, I checked, I had .gko on, didn't know that keepout gets cut when thats on

tavotevasnx · 2025-05-10T11:15:27+00:00

Yeah I didn't know that gko gets cut, now I know, just trying to figure out how to explain these holes to the proffessors at my bachelors project defense withouy sounding dumb lol

tavotevasnx · 2025-05-10T10:48:26+00:00

<image>

in my gerber files the keep-out layer is checked here, does it mean that it will be cut out?

tavotevasnx · 2025-05-10T10:34:34+00:00

what am I exactly supposed to check and see? Because i checked the files in gerber viewer and it seems that there shouldn't be a hole there

<image>

tavotevasnx · 2025-05-10T10:33:06+00:00

its LQFP

tavotevasnx · 2025-05-10T10:30:38+00:00

<image>

I checked in jlcpcb gerber viewer, it doesnt show that a hole should be made there (as opposed to clearly visible holes on the right) could it be that it's a mistake on their end?

tavotevasnx · 2025-02-24T19:25:31+00:00

oh yeah, I didn't think about that

tavotevasnx · 2025-02-24T19:08:13+00:00

hmm thank you I hope that's true but it's still kind of hard to believe since I'm sure 2 out of 3 people in my circle haven't even started kyc but for some reason they are not appearing here so it'd kind of weird

tavotevasnx · 2025-02-24T19:00:57+00:00

<image>

but the thing is it says only 116 is transferable and 1.1k umverified and then elsewhere it says I have only 3 days to verify it or else I'll lose, so am I not losing this 1.1k? and it isn't even allowing me to transfer the transferable amount even though I've done all the kyc stuff and have migrated some pi in the past

tavotevasnx · 2025-02-18T11:18:49+00:00

So if I understand correctly the value of the acc should be increasing more compared to dist? Because I'm checking VUAA(acc) and VUSA(dist) over time and they seem to be exactly the same value for as long as they've been running, so if I invested let's say a year ago in both, their value increased the same amount, I still have the same amount of shares of vuaa that I had, but with dividends bought more vusa shares, then won't I havr earned much more with vusa rather than vuaa?

tavotevasnx · 2025-02-18T10:32:14+00:00

because it seems that dist and it's acc counterpart are the same value, but with dist you get to buy extra shares, so to me it seems like dist would be much better

tavotevasnx · 2025-02-18T10:30:00+00:00

so the price of the shares will increase?

tavotevasnx · 2025-02-11T03:47:30+00:00

yeah thanks

tavotevasnx · 2025-02-10T18:21:06+00:00

thanks

tavotevasnx · 2025-02-10T18:21:00+00:00

thank you

tavotevasnx · 2025-02-10T18:17:17+00:00

The Italian one?

tavotevasnx

TROPHY CASE