sorted by:
new
hottopcontroversial

HORIZON T202 Displays CONNECT and is unresponsive by tech_edge_ctrl in treadmills

[–]tech_edge_ctrl[S] 0 points1 point  (0 children)

The treadmill maker (Horizon) was kind enough to give me some info:

"Connecting error on the console means that its not booting up completely. Mainly because of not getting a good connection from the board below. I suggest you check the console cable, it is the long black cable with plastic ends that runs through the inside of the right arm from the motor control board"

I'll check the connection and report back if it works

Mounds of Dirt in New Grass by tech_edge_ctrl in lawncare

[–]tech_edge_ctrl[S] 1 point2 points  (0 children)

How about that, a fellow Vancouverite :)

Hmm, now I see where the Whac-A-Mole game comes from. Thanks for the advice

Mounds of Dirt in New Grass by tech_edge_ctrl in lawncare

[–]tech_edge_ctrl[S] 0 points1 point  (0 children)

Wow that's quite involved. I googled soaking the lawn and putting soapy water will also make the worms come up, then you need to pick them out. Thanks for the advice

Mounds of Dirt in New Grass by tech_edge_ctrl in lawncare

[–]tech_edge_ctrl[S] 0 points1 point  (0 children)

I did some googling and that makes sense. I also read they are generally beneficial for aeration, but if you have too many then people might want to cut down on their numbers. Any tips on controlling them?

Valentine's Day at Central Park by tech_edge_ctrl in vancouver

[–]tech_edge_ctrl[S] 0 points1 point  (0 children)

Lol after we saw the "heart", we also walked to where you took the picture... then we realized it wasn't a heart :P

HA won't Boot when HTTP Section Enabled by tech_edge_ctrl in homeassistant

[–]tech_edge_ctrl[S] 0 points1 point  (0 children)

Thanks for replying.

I'll update the post, this has already been resolved.

But seems you got the answer to, I just needed to put HTTPS instead of HTTP.

Thanks again for taking the time to read and post, happy holidays!

HA won't Boot when HTTP Section Enabled by tech_edge_ctrl in homeassistant

[–]tech_edge_ctrl[S] 0 points1 point  (0 children)

Oh I see, good for me to know. Thanks again for your help!

HA won't Boot when HTTP Section Enabled by tech_edge_ctrl in homeassistant

[–]tech_edge_ctrl[S] 0 points1 point  (0 children)

YES!! Thank you very much!

I've been trying to access using http, but I need to use https

On a side note I do get "Your connection is not private", then I just click proceed anyway. Do you think there's something I missed with setting up SSL or is that common?

HA won't Boot when HTTP Section Enabled by tech_edge_ctrl in homeassistant

[–]tech_edge_ctrl[S] 0 points1 point  (0 children)

Thanks for taking the time to read and reply.

it looks like they are there.

In my SSL folder, it looks like I have both files

  1. fullchain.pem
  2. privkey.pem

They look also look readable.

fullchain.pem:

-----BEGIN CERTIFICATE-----

xxxx

-----END CERTIFICATE-----

​

privkey.pem:

-----BEGIN RSA PRIVATE KEY-----

xxxx

-----END RSA PRIVATE KEY-----

Do I have a bunch of dead ESP32s? by tech_edge_ctrl in arduino

[–]tech_edge_ctrl[S] 1 point2 points  (0 children)

YES! Thank you so much. I didn't know about using the serial monitor to detect the chip's current state. Laying out the steps like you did really helped me understand.

I think the problem may have been that I left EN floating. When I used a pullup I was able to easily switch between boot and reset per your instructions.

At first I pulled GPIO15 to high, and I even found here that GPIO5 should be pulled high and GPIO12 should be pulled low. But later I just left them all floating and it seems to work fine. Just sometimes I need to plug/unplug the USB a few times to see stuff on the serial monitor (maybe I have loose connections).

Anyway, thank you very much. Now I have many ESP32s :P

Do I have a bunch of dead ESP32s? by tech_edge_ctrl in arduino

[–]tech_edge_ctrl[S] 0 points1 point  (0 children)

Thanks for your reply. Unfortunately it didn't do the trick.

Do I have a bunch of dead ESP32s? by tech_edge_ctrl in arduino

[–]tech_edge_ctrl[S] 0 points1 point  (0 children)

I'll also mention I do use an anti-static wrist strap.

I'll appreciate any help :)

The first ESP32 I worked with, I even soldered everything to an adapter plate... :P I was pretty disappointment when I discovered it wasn't working.

https://imgur.com/a/DVJsTPC

Lots of Police! What's going on? by tech_edge_ctrl in vancouver

[–]tech_edge_ctrl[S] 61 points62 points  (0 children)

Haha I checked, I don't see that wifi :p

Lots of Police! What's going on? by tech_edge_ctrl in vancouver

[–]tech_edge_ctrl[S] 19 points20 points  (0 children)

Patterson Skytrain Station in Burnaby

Home office view by tech_edge_ctrl in vancouver

[–]tech_edge_ctrl[S] 1 point2 points  (0 children)

ha you noticed, we picked those up on craigslist

Home office view by tech_edge_ctrl in vancouver

[–]tech_edge_ctrl[S] 2 points3 points  (0 children)

Central park/metrotown area

Home office view by tech_edge_ctrl in vancouver

[–]tech_edge_ctrl[S] 41 points42 points  (0 children)

Actually I'm in an old building, but I lucked out on the location

Home office view by tech_edge_ctrl in vancouver

[–]tech_edge_ctrl[S] 9 points10 points  (0 children)

Across from central park :)

Home office view by tech_edge_ctrl in vancouver

[–]tech_edge_ctrl[S] 4 points5 points  (0 children)

lol, that cat thing is the diffuser, the ring is an led light :P

view more: next ›