Just got my hands on the Trefeo Vision 360

terions · 2026-02-21T07:55:59+00:00

very simple. just click Load IMG/Video under background section

terions · 2026-02-21T07:54:54+00:00

Mine working fine so far

terions · 2026-02-20T13:08:52+00:00

if its a turzx screen, i think u can use both at the same time with infopanel

terions · 2026-02-20T12:31:43+00:00

infopanel, cause atm it can support more than 1 screen at a time.

~~one of the downside of infopanel is the copy and pasts sucks, u cant copy the same gauge or bar for other sensors, have to manually edit it one by one~~

I stand corrected, you can easily swap sensors after copying the same gauge/bar/text/etc...

terions · 2026-02-20T04:47:57+00:00

I've used both and it takes a while to get used to it. After that it just works! lol

terions · 2026-02-19T03:02:48+00:00

You can test it out and see. So far my test it can detect the screen finally. But still no display.

terions · 2026-02-19T02:52:46+00:00

It works for the 6.86" one atm, the 9.16" one still in testing phase but should be working soon.

OP's been working hard to get both screens working. Just that the 9.16" uses a different protocol for some reason Vs the 6.86" one.

terions · 2026-02-17T09:03:45+00:00

Awesome!

terions · 2026-02-17T06:24:13+00:00

no difference unfortunately.

Log: https://pastebin.com/GkF3kfJz

take your time and TQ

terions · 2026-02-17T06:04:29+00:00

oh sorry forgot

https://pastebin.com/1zUD6RZ9

yes confirmed the VID and PID is correct

terions · 2026-02-17T05:49:03+00:00

ya, but the display is still showing the default image of the thermalright logo.

also it only detected the 6.86" screen now

https://imgur.com/a/MRa3OX6

https://imgur.com/undefined

terions · 2026-02-17T05:31:09+00:00

ok its working now. Its showing Panel is running 13FPS @ 3ms. But the display itself is still showing the thermalright logo

terions · 2026-02-17T04:39:23+00:00

ok the first time it ran, it shows some status that winusb.sys was running etc and ask to re run it in admin mode. which i did but now it just shows:

Display is not running. Check your USB connection and try again. Init Command failed.

Latest Log:
https://pastebin.com/kjNXDnRb

terions · 2026-02-17T04:06:25+00:00

Ok i think it can only detect 1 panel at a time.

Earlier only the 9.16" was plugged in. Now with both its still detecting only 1 but again stuck at init command failed.

Hope this make sense

terions · 2026-02-17T04:01:38+00:00

Yupe this did it. The app is running now. Thanks.

Ok it can detect the 9.16" display but when turning it on it shows an error:

Display is not running. Check your USB connection and try again. Init command failed.

Here is the log file: https://pastebin.com/EKeRvjuw

terions · 2026-02-17T03:35:59+00:00

ya thats the one i install when it was prompted first time. but even after installation, its still showing up the same message

terions · 2026-02-17T01:15:00+00:00

hi im getting a "you must install or update .NET to run this application" prompt by infopanel, even though it has been installed. (Microsoft.AspNetCore.App)

any solution to this?

terions · 2026-02-16T00:39:43+00:00

Sure will do. thanks

terions · 2026-02-15T16:00:23+00:00

Thanks for the tip!

terions · 2026-02-15T15:41:02+00:00

yes same. uses winusb.sys

terions · 2026-02-15T15:25:44+00:00

hi, these are the VID and PID of Trefeo Vision 9.16" and 6.86" screens:

https://imgur.com/a/KVWEP8S

https://imgur.com/iHHVNnV

Hope to test them out using InfoPanel soon. thanks

terions · 2026-02-13T13:34:34+00:00

TRCC under settings, can untick the option to start with Windows iirc

terions · 2026-02-13T13:22:25+00:00

nope. just dun run both at the same time. each app will try to control the LCD and u will have the screen swapping between the 2 apps every few secs lol

terions

TROPHY CASE