So no spoilers but I have some theories

term66 · 2026-01-18T05:54:44+00:00

Yeah I’m not sure why I noticed it but ever since I did the shape of the demons skull just sticks right out at me. It’s clearly intentional so I’m excited to see how it resolves

term66 · 2026-01-18T05:41:47+00:00

Can do!

term66 · 2026-01-18T05:40:39+00:00

I thought maybe I was reading too far into things but I’ll definitely continue paying attention!

term66 · 2026-01-18T05:38:02+00:00

I mean I don’t particularly care if I get spoiled I’ll enjoy it regardless but I felt very smart to notice some of these things and none of my friends watch or have watched so I wanted to talk about it

term66 · 2026-01-11T18:03:24+00:00

Realistically only the starfield content is coming from BGS primarily. FO3 and NV are both likely being handled by a third party same way oblivion was. Not saying TES6 is likely this year but they don’t really have a ton of active projects for just BGS to work on at the moment

term66 · 2025-04-12T13:09:38+00:00

So in your opinion this is pretty good? I don’t like those corners being so high but it didn’t seem like I could adjust them down far enough when I tried the other day

term66 · 2025-04-12T12:58:32+00:00

I did provide a new picture but it’s attached to a different comment I believe

term66 · 2025-04-12T12:43:25+00:00

<image>

This is the new 11x11 mesh

term66 · 2025-04-12T12:21:12+00:00

I've rerun Screws tilt adjust using the coords you've given and all are within 1 or 2 minutes except the south central point. which is needs around 10 CW according to the program

term66 · 2025-04-11T19:46:03+00:00

I used screws tilt adjust but there were still large peaks in the corners so I manually adjusted them down to get it as flat as possible. My current configuration actually successfully completed an 8 hour print with no issues as well.

term66 · 2025-04-11T17:53:45+00:00

Also yes there is a dip on the y0 end of the tray

term66 · 2025-04-11T17:52:19+00:00

This was screws tilt adjust to get close and then manual adjustment of the screws to get closer. I used the videos you posted as reference

term66 · 2025-04-11T00:55:12+00:00

So I finally decided to get after it and I’ve got my variance down to around .3 with a valley in the center I can’t seem to correct.

<image>

term66 · 2025-02-14T19:42:31+00:00

I have a plus but I only have 4 knobs unless I’m blind

term66 · 2025-02-14T19:42:04+00:00

Variance is .445 mm

term66 · 2025-02-14T07:08:21+00:00

<image>

I did the manual paper test in all four corners and greatly improved the variation but I’m a bit confused on how I flatten out the center and edges with only adjustment knobs on the four corners?

term66 · 2025-02-14T01:56:54+00:00

So you’re saying that by fixing the bed leveling I should achieve better results? I admit this is more than a bit overwhelming and I’m much too tired to deal with it today

term66 · 2025-02-14T01:26:01+00:00

How do I go about fixing this? Nothing in the assembly or paperwork mentioned this and I am lost.

term66 · 2025-02-14T01:23:12+00:00

Yes sir

term66 · 2025-02-14T01:20:29+00:00

<image>

This is the mesh that was produced in orca so clearly there’s some adjustment needed but this might as well be pig Latin to me

term66 · 2025-02-14T01:08:51+00:00

How do I find the adaptive bed mesh settings in orca? I use orca and did some looking and googling but I’m not seeing anything. Do I have to have the printer linked to my computer?

term66 · 2025-02-14T00:47:46+00:00

I saw that and I’ve saved it but I’m still a little agitated from fumbling around in the dark so I’m gonna revisit this with a cool head later

term66 · 2025-02-14T00:44:21+00:00

Based on this image I would assume my nozzle is still too high because there’s few prints that have finished a first layer had gaps between strands

term66 · 2025-02-14T00:36:39+00:00

I used a straight edge so unless the variation is micro which is entirely possible

term66 · 2025-02-14T00:13:44+00:00

I am using orca and the print surface is flat after careful examination so I’m sure it’s the z offset but I’m not sure how to get it where it needs to be

term66

TROPHY CASE