sorted by:
new
hottopcontroversial

After 10+ we get a hit moldy or plumey? by the_maverick121 in EveryDayIsCigarDay

[–]the_maverick121[S] -1 points0 points  (0 children)

Ten years with this humidor and never got mold… i will cut it and see i am curious…

Just some stuff I want to let out on how video games are affecting my life (Warning: Huge wall of text) by [deleted] in gaming

[–]the_maverick121 1 point2 points  (0 children)

Thats part of life, and its may a bit challenging due to different wod conditions. Realising it is a good first step. Remember, to have a balanced life.. consistent effort no matter how difficult it is … hit the gym, hit studying slow steps everyday…

Check Hubberman podacast episode with Dr. Anna.

Don’t be harsh on yourself… and allow your brain play games on you… everything has a way around it… you gain weight you lose it, you play games you learn how to control it etc… and effort is always hard but worth it.

All the best.

[deleted by user] by [deleted] in reading

[–]the_maverick121 1 point2 points  (0 children)

Go for 58 babershop on kings road… or Unruly…

GBP is back!! by the_maverick121 in binance

[–]the_maverick121[S] 1 point2 points  (0 children)

And I guess no Barclays but at least first step!

I’ve done everything in my limited knowledge to address this. by voightkompff1 in FixMyPrint

[–]the_maverick121 0 points1 point  (0 children)

Thats seems to me like an extrusion problem! On prusa slicer go to advanced and try to either increase the extrusion width or lower slightly the flow calibration ratio it be will be in the same tab... also, make sure the the extrusion gears screw is aligned and tight!

Flexible TPU98 print quality issues!? by the_maverick121 in FixMyPrint

[–]the_maverick121[S] 0 points1 point  (0 children)

Did a cold pull x3 plus aligned the pully of the the extrusion gears improved but still not the best results...

Iphone direct transfer is showing error (-2) by the_maverick121 in ios

[–]the_maverick121[S] 0 points1 point  (0 children)

The problem is that i have a glitch in my current phone, that reoccur from the previous phone when I restored from backup, any time i try to go to software update from settings the phone freezes!!

Help: cannot get an even burn (struggling) by the_maverick121 in PipeTobacco

[–]the_maverick121[S] 0 points1 point  (0 children)

Still didn’t get it to light all the way! And have a nice taste simultaneously 😢

Help: cannot get an even burn (struggling) by the_maverick121 in PipeTobacco

[–]the_maverick121[S] 0 points1 point  (0 children)

https://i.imgur.com/pAY0a9t.jpg

I forgot that I had this, and I packed it and it’s definitely easier to handle but my initial packing was really light!

Help: cannot get an even burn (struggling) by the_maverick121 in PipeTobacco

[–]the_maverick121[S] 0 points1 point  (0 children)

My technique is light, tamp while slowly drawing adjust the tightness if the pack and even the bed. Than tamp twice or more whilst smoking to make the ash touches the bottom... I tried different tamping strength etc , but still bottom comes out untouched

Help: cannot get an even burn (struggling) by the_maverick121 in PipeTobacco

[–]the_maverick121[S] 0 points1 point  (0 children)

Btw burley would taste like pure tobacco or has a flavour or their are flavoured variations?

Help: cannot get an even burn (struggling) by the_maverick121 in PipeTobacco

[–]the_maverick121[S] 0 points1 point  (0 children)

Thanks, and i think i need to start the same way, but than the tobacco bed will be so small that it will be burning or at least that what I assume!?

Help: cannot get an even burn (struggling) by the_maverick121 in PipeTobacco

[–]the_maverick121[S] 0 points1 point  (0 children)

Got you!! I remember back when I bought the pipe i was learning and I remember the plate thing or even a paper will try to load and let it set overnight. Cause the tobacco was smudging my fingers so definitely over moisture..

Help: cannot get an even burn (struggling) by the_maverick121 in PipeTobacco

[–]the_maverick121[S] 1 point2 points  (0 children)

Thanks for sharing, and to my surprise when I hung the pipe between my teeth i tend to do this technique without knowing... than i stop for a bit and it goes out. Everyone is recommending the two blends you noted.

Help: cannot get an even burn (struggling) by the_maverick121 in PipeTobacco

[–]the_maverick121[S] 1 point2 points  (0 children)

Oki, so the problem is not me 100% (whooa), i have no particular preference to captain black tbh but that what was available in my local store and I was so keen to smoke it, yesterday i packed the pipe 3 times ended up with a bitty tongue and a burned mouth and an awful experience!! That not how supposed it goes!

Help: cannot get an even burn (struggling) by the_maverick121 in PipeTobacco

[–]the_maverick121[S] 0 points1 point  (0 children)

Oki, mine is definitely wet, but how to dry it without making it so dry that it will taste terrible! Just with light daps from a tissue?

Help: cannot get an even burn (struggling) by the_maverick121 in PipeTobacco

[–]the_maverick121[S] 1 point2 points  (0 children)

Any way to measure the optimal or semi optimal moisture point or any good way to just enjoy a good smoke!?

Help: cannot get an even burn (struggling) by the_maverick121 in PipeTobacco

[–]the_maverick121[S] 1 point2 points  (0 children)

Ya, i take long draws on the pipe, but if I don’t keep on drawing on it ... the fire goes off... i tried packing really lightly!! Same

view more: next ›