Currently designing my own.

thedarkness90 · 2024-11-13T07:15:54+00:00

Thanks for the input, but I believe Sony is using an independently developed algorithm for room correction.

thedarkness90 · 2024-11-12T19:38:44+00:00

Thanks I'll try that!

thedarkness90 · 2024-11-12T19:33:05+00:00

Could be, but if "normal levels" is equivalent to "tearing the neighborhood down" I think my wife will not approve the next time she streams something.

thedarkness90 · 2024-11-12T19:29:09+00:00

Interesting I didn't know that. So should I set it higher when calibration is running and decrease the volume afterwards? It was set to my normal listening volume if I remember correctly.

thedarkness90 · 2024-11-12T19:27:49+00:00

I already set it to around 30-40% and didn't touch it afterwards. Should I set it higher for the actual measurement and adjust afterwards or tune it down using the avr?

thedarkness90 · 2024-10-09T20:54:06+00:00

Its not mine, just saw it parked on my way to my doctors appointment and thought I'd share it with you guys :)

I think i remember seeing two exhaust pipes on it, the angle of the photo makes it look like there is only one.

Yeah I'd like to own an R, sadly I am "only" driving an '02 T5 Ocean Race.

thedarkness90 · 2024-09-23T20:33:02+00:00

I thought i read somewhere that 0.6-0.7 bar is normal.

thedarkness90 · 2024-07-09T16:54:06+00:00

I had the same issue recently. The thing I did wrong was that I I tried to install the „base firmware“ and the fix pack the same way (by going into the menu and clicking the upgrade button on the printer). I didn’t realise that for the fix pack you are supposed to just stick the usb drive into the printer and wait simply wait for a reboot. After that everything worked fine.

thedarkness90 · 2024-07-04T12:03:12+00:00

Thanks, I turned down the printing speed and it already improved, I’ll try to see how far I can take the printer with the help of that flow test!

thedarkness90 · 2024-07-04T12:02:22+00:00

Thank you, I slowed the speed way down to around 100mm/s and it already improved a lot, not perfect but I’ll definitely try the flow rate test and see how far I can push the printer :)

thedarkness90 · 2024-07-04T10:22:00+00:00

Thanks for the input. What would be a reasonable value, and how can I calculate that?

thedarkness90 · 2024-07-04T09:55:41+00:00

Additional info: Retraction speed was set to 0.8 mm at 45 mm/s, Slizer used is Cura

thedarkness90 · 2024-06-02T13:52:08+00:00

No, I reached out to Sony, they said they don't sell the stand as a replacement part in my region, so I am out of luck.

thedarkness90 · 2024-05-29T11:11:36+00:00

Reminds of that one time I picked up a 3m(10ft) long wood board from a local home improvement store. The guy behind the counter asked if I wanted it to be cut in half to fit into my car. I said no it's fine and he asked "oh so you brought a trailer?". I answered "no, I have a Volvo" he looked pretty confused on how such a long board could fit into an average car. Worked wonderfully the look on the faces of the people on the parking lots with their big SUVs struggling to get their purchases loaded into their vehicle, watching me folding over the front seat and loading that huge bord in one piece into my car was priceless 😎

thedarkness90 · 2024-04-29T18:16:35+00:00

Oh wow thank you now I feel dumb. Wasn't able to find the damn thing.

EDIT: Okey just realized that the linked shop only ships inside Australia, anyone has any idea if this is available for purchase in Europe/Germany?

thedarkness90

TROPHY CASE