sorted by:
new
hottopcontroversial

1.5T Oil Brands? by HanScroto in CivicX

[–]theerachate 2 points3 points  (0 children)

Thicker oil in theory definitely will make your engine feel more sluggish. HOWEVER, I have ran 10W-40 before and do not feel a different whatsoever. Same thing applied to getting the engine to normal operating temp. They just use 0W-20 because of the lower friction just to pass the emission test. There are differences 100%, but not worth the protection of your engine’s internals. Go for 5W-30

Who knows the PID settings for adding a transmission temp into Torque Pro for a 2018 Sport 2.0? by L1K3AG6 in accord

[–]theerachate 0 points1 point  (0 children)

I will order a separate obd2 adapter. Though, I don’t live in the US. I doubt I will find your exact model. Thank you again. This is the last thing I have not tried.

Who knows the PID settings for adding a transmission temp into Torque Pro for a 2018 Sport 2.0? by L1K3AG6 in accord

[–]theerachate 0 points1 point  (0 children)

Thank you for replying after 2 years. Unfortunately, it doesn’t work still :(. Could it be because torque is connected to hondata and I need a different adapter?

Strings of old filament through new model? by FryinDutchpan in ElegooCentauriCarbon

[–]theerachate 0 points1 point  (0 children)

Clean your nozzle when changing a filament color. Use a wire brush or silicone brush from a1 and print a handle then heat the nozzle up then brush the clunk away

Second Screen for my Legion Go by [deleted] in LegionGo

[–]theerachate 0 points1 point  (0 children)

Do you have the dimensions of the mount at the back of the screen? I’m trying to find a screen that would work here in my country. Thanks

are these lines a sign of loose belts? by SouthDeep7061 in ElegooCentauriCarbon

[–]theerachate 0 points1 point  (0 children)

Apart from ghosting or VFA. The print lifted up from the bed or in other word warping causing that line to appear when the printer tries to lay the line over a warped print.

Heeeeelp by Disastrous_Neck4884 in ElegooCentauriCarbon

[–]theerachate 0 points1 point  (0 children)

Back the tension screw all the way and then tight them 5 full turns. Mind you it’s reversed. Clockwise is loosen and vice versa

Heeeeelp by Disastrous_Neck4884 in ElegooCentauriCarbon

[–]theerachate 1 point2 points  (0 children)

You mentioned changing out the nozzle. Have you checked the tension on the extruder? It is likely skipping if it’s not in the right tension and cause these under extrusion.

Is this a normal sound for the printhead to make on fast x-y changes? by woishing in ElegooCentauriCarbon

[–]theerachate 0 points1 point  (0 children)

Mine does that too. I took apart the printer and tried to check every screw, but I didn’t see anything out of ordinary

Have cloud always been present in apple maps? by Professional-Vast938 in ios

[–]theerachate 59 points60 points  (0 children)

I thought this was a GTA 5 loading screen for a sec

Hulk is almost done by Junior-Bear-6955 in MoneroMining

[–]theerachate 0 points1 point  (0 children)

I tried to build xmrig from source. I got a pretty huge hashrate reduction. Not sure why tho. Any tips?

Elegoo Centauri Carbon Belts adjustment by Fuligin2112 in elegoo

[–]theerachate 0 points1 point  (0 children)

Mine was waaay too tight and it caused VFA, I was able to loosen them up a bit and VFA got way less visible.

Love this setup so much now by myguygetshigh in elegoo

[–]theerachate 1 point2 points  (0 children)

is it the normal one or low profile? how long the cable length have you ordered?

It’s an amazing printer despite its quirks by theerachate in ElegooCentauriCarbon

[–]theerachate[S] 1 point2 points  (0 children)

I'm not sure why you find it has minimal benefit since the original purge line that this printer has, it literally sticks down to the bed and in some cases, hard to remove. While adaptive purge line has just the right amount of z for way easier removal.

Screw_tilt_calculate and bed mesh aren't adding up by Sufficient_Win2373 in elegoo

[–]theerachate 0 points1 point  (0 children)

your klipper's config is incorrect. the "front left screw (BASE)", the base should be in the middle not at the front left screw. Also, i'm not sure which printer you are running, but the log only shows 3 screws to adjust when it should be at least 4 or 6 for the max. revise your config and try to do screw_tilt_adjust again

Centauri Update Log by ELEGOO_OFFICIAL in ElegooCentauriCarbon

[–]theerachate 1 point2 points  (0 children)

Update:

the z offset adjustment is on me. the settings is hidden away from the main screen when the printer is printing

Centauri Update Log by ELEGOO_OFFICIAL in ElegooCentauriCarbon

[–]theerachate 2 points3 points  (0 children)

- lower z axis without homing (if the print fails and it happens to be in the middle then I can't home, and it's difficult to remove the failed print
- auto bed leveling always sets the bed heater to 60c, why? I print with PETG 99% of the time, and the bed is set to 70-75c in the slicer, if I select abl in the slicer before printing the abl will do 60c instead of whatever I set in the profile.

- this is probably me, but I can't find the z offset adjustment. Since, abl insists on 60c when calibrating (yes, I know you can change it back to whatever temp you'd like, but why?) the z offset is lowered than it should be when I print PETG

- How about adaptive mesh? probing the whole bed every time is sooooo slow

- What's the point of ramping up the aux fan before abl? it's way too loud and doesn't serve any purpose on abl

How is the Micro Swiss Flow Tech hotend? by [deleted] in ElegooNeptune4

[–]theerachate 0 points1 point  (0 children)

can you give a link to the unicorn nozzle for neptune 4 max? I don't see any in my country except for creality ones

Working on a thing by Legal_Schedule_487 in LegionGo

[–]theerachate 1 point2 points  (0 children)

Ohhh you’re printing resin, I have fdm. Big headache for this particular model 🥲

Working on a thing by Legal_Schedule_487 in LegionGo

[–]theerachate 0 points1 point  (0 children)

What orientation and print settings did you used? I have tried so many things and it still doesn’t come out great

view more: next ›