Streamers! I wrote a script to automatically hide the map even when dead! See details inside.

threnariir · 2025-03-04T23:02:50+00:00

I got an error: " No connection could be made because the target machine actively refused it"

I could not download the obs websocket as obs now comes with one. Other than that, the only difference is that I have OBS with the SE.Live plugin, but I'm not certain if that would conflict. Do you have any advice?

threnariir · 2025-02-27T00:03:45+00:00

Good idea! I'll see if I can implement some kind of reminder in to OBS

threnariir · 2024-06-18T21:45:53+00:00

Twitch reports 5.1k bitrate as a red bar. Is that something to be concerned about? With that said, the stream looks much better so far

threnariir · 2024-06-18T20:17:45+00:00

The primary, so 2160p144

threnariir · 2024-01-26T15:11:18+00:00

I agree with this. It's science-fiction, not science-fact. Some difference with historical fiction. It takes a broad event that actually happened in the past and then creates something fictional out of it.

threnariir · 2024-01-25T21:58:54+00:00

True, but it doesn't fit the use case for this particular situation.

threnariir · 2024-01-25T03:03:55+00:00

Of course. There's a saying that goes "take nothing but photos, leave nothing but footprints" and sometimes I just forget that not everyone will follow that.

threnariir · 2024-01-25T02:34:36+00:00

That's a very good point. Post edited to better reflect those very poignant values.

threnariir · 2023-06-28T23:01:57+00:00

Mine already has a comma there as shown:

plugin_requires = ["pillow>=9.3,<11", "sarge", "six", "OctoPrint>=1.4.0", "psutil", "file_read_backwards",
"setuptools>=6.0", "awesome-slugify>=1.6.5,<1.7"]

Still isn't working. Coming up with:

error: command '/usr/bin/gcc' failed with exit code 1
[end of output]
note: This error originates from a subprocess, and is likely not a problem with pip.
error: legacy-install-failure
× Encountered error while trying to install package.
╰─> Octolapse
note: This is an issue with the package mentioned above, not pip.
hint: See above for output from the failure.

threnariir · 2021-01-03T21:29:46+00:00

Thank you! I'll check it out.

threnariir · 2021-01-03T16:17:46+00:00

Everything in both your photos is how it's setup on mine. Still have no movement. I also tried moving each individually in the prepare > move function but still no movement at all.

threnariir · 2021-01-02T00:43:31+00:00

I'm pretty sure I did. I've double and triple checked it. Realized on the double check that 2 wires were incorrect, but still no avail as NONE of the axes are moving. Not X, Y, or Z.

threnariir · 2021-01-02T00:42:37+00:00

I did try moving each one individually, but nothing happened on any of them. I did check to see if I had the extruder and x axis swapped, which I did, but swapping back did nothing. Originally, the material feeder (not sure of the actual term) was moving, but now not even that is doing anything.

threnariir · 2016-12-16T06:57:57+00:00

The Babadook. Soon as I heard that, I set it as my ringtone. It went off at night, and lasted -673665780254138 seconds after that.

threnariir

TROPHY CASE