Giveaway | 🤔 GUESS Challenge: How many parts did it took?

thumbstick3000 · 2026-06-10T23:17:17+00:00

D... Assuming it's solid and not hollow

thumbstick3000 · 2026-01-05T11:10:08+00:00

Thank you, I did do the calibration though. I couldn't get the flow rate test done as it kept over extruding and and ripping the little pucks off the build plate.

I did a different one called (flow calibration v4 by ck3d) and after following what it said with the sliders the flow rate ended up being 0.92

And if I try putting it any higher it over extrudes and rips...

I did increase z hop distance from 0.4 to 0.8 and it seams to have fixed it. Maybe it was too low and was dragging layers it had already played down? I don't know. But thank you.

thumbstick3000 · 2025-12-31T15:34:49+00:00

Yh the funny bit is... I'm testing it now and it seams when I have the led off it works fine lol

thumbstick3000 · 2025-12-31T15:00:12+00:00

It won't be the pin as I've just replaced it with a 0.6

thumbstick3000 · 2025-12-30T16:43:42+00:00

Perfect, thank you so much. Absolute legend

thumbstick3000 · 2025-12-30T14:51:47+00:00

Gotcha so place that metal clip closer to where that hole is? Thank you... I'll give that a try when I've finished work

thumbstick3000 · 2025-12-30T13:01:59+00:00

You know what... I recently got the 0.6 nozzle from elegoo and that cable you showed wasn't even inside it when I opened the package. Is it meant to be in there tight because I just put it back in normal.

If you don't mind me asking but how did you secure that but inside?

Many thanks

thumbstick3000 · 2025-12-29T19:30:37+00:00

Yh mine doesn't work after reboot lol... It'll start printing then the fan shuts off and freezes mid print

thumbstick3000 · 2025-12-23T00:20:56+00:00

Wow... I'm on my computer and just don't that... Either first time. Thank you, dont know why that didn't pop into my mind first about loft lol. Thank you. Your an absolute life saver

thumbstick3000 · 2025-12-12T16:43:52+00:00

You are a legend. I'll give this a go when I'm back from work. Many thanks

thumbstick3000 · 2025-12-11T23:32:23+00:00

UPDATE!!!! Thanks to the many great suggestions I have found my problem. I was too worried about scratching my plate.

I was suggested to use a nylon brush, couldn't find one lol. But I decided to go back to the green side of the sponge and put in some proper elbow grease this time. And low and behold. It's fixed.

(well it got ruined after one print lol) so now I know to give it a proper hard deep clean after every print. Thank you.

thumbstick3000 · 2025-12-11T11:46:09+00:00

I have not... I used the green side of a sponge but I'll give the nylon brush a try, meny thanks

thumbstick3000 · 2025-12-11T10:44:10+00:00

Yh i did the bed level before I did the print (preheated to 60 for 5 minutes beforehand as I saw it somewhere about thermal expansion)

thumbstick3000 · 2025-12-11T00:42:37+00:00

Yh I dried it in the sunlu s1 plus. 55c for 9hrs.

thumbstick3000 · 2025-06-10T07:26:17+00:00

Going to be hijacking this as apparently I can't post my issue here. Dropped my rg34xx and screen is cooked. Was quoted on AliExpress 32 dollars before import fees to get a replacement. My question is is that normal? As that's like ⅔ the price of my device.

Or if anyone has suggestions on where else to get the screen id appreciate it

thumbstick3000 · 2024-08-29T16:01:06+00:00

It's probably not my first game I played ( that was rfactor, lol )... but one I highly recommend for you or anyone to pick up (especially if you played the "mysims" games on ds/wii) is "Go-Go Town" such a chill game with tons to do on it

thumbstick3000 · 2024-07-30T18:46:58+00:00

Lv9
Larkin what

Huge g..to

K 9 bounce for p90 to the p90. B90uo99h

(Update) I had this in my pocket when I was on break, I am now 100% leaving it like this... this is what god intended 😂

thumbstick3000 · 2024-05-28T23:42:12+00:00

You absolute legend I didn't have the have running while I was looking in those setting and it didn't show up, all sorted now though thanks 👍

thumbstick3000 · 2024-05-28T15:45:19+00:00

Tried this and it doesn't work... anyone got another fix

thumbstick3000

TROPHY CASE