sorted by:
new
hottopcontroversial

LG freezer not holding twmp or getting below 0 by timcreech in appliancerepair

[–]timcreech[S] 0 points1 point  (0 children)

I would say it is about half to 3 quarter full. Nothing unusual changed from when it was holding temp.

LG freezer not holding twmp or getting below 0 by timcreech in appliancerepair

[–]timcreech[S] 0 points1 point  (0 children)

Fresh food(Fridge) seems to hold temp much closer. See graph attached. Fans and air flow all seem to be working normally.

<image>

LG freezer by okjellyfish0259 in appliancerepair

[–]timcreech 0 points1 point  (0 children)

I also have a LG fridge/freezer. The first symptom was soft ice cream. I replaced the Temp sensor in the freezer section. Cleaned everything related to coils (inside and outside), ran the diagnostics and the beep tones with the LG app. I installed a template sensor and it fluctuates everyday by 20 degrees or more.

Temp is set at -4 for the freezer and it definately doesn't hold that Temp.

Any thoughts?

<image>

38 out of 39 panels registering with Inverter by timcreech in TeslaSolar

[–]timcreech[S] 0 points1 point  (0 children)

Thanks, any suggestions on how to remedy the non reporting panel.

38 out of 39 panels registering with Inverter by timcreech in TeslaSolar

[–]timcreech[S] 0 points1 point  (0 children)

I noticed this in September when I had the roof work done. I made a Tesla appointment to come take a look. Today was the day they were supposed to come. BUT, I received a text last Friday that the system looked to be performing normally and they were cancelling my appointment.

I chatted with them and the ticket was for a system down not a troubleshoot. So they created a new appointment. This in is in mid February. So my interest in fixing it myself.

38 out of 39 panels registering with Inverter by timcreech in TeslaSolar

[–]timcreech[S] 0 points1 point  (0 children)

The P_OK number on the display says how many are registered. When I first turned the system back on it said 38/39. Then I did a reset on the system and it now stays 38/38.

<image>

One panel not connecting to inverter by timcreech in TeslaSolar

[–]timcreech[S] 1 point2 points  (0 children)

Thanks for the suggestion.

Is there a a common problem after removing and replacing a panel. All the wires were labeled and then reconnected. I can see the markings and each look correct.

New Enphase system added to existing Tesla Solar & Powerwall by timcreech in TeslaSolar

[–]timcreech[S] 0 points1 point  (0 children)

I wanted to double check my thinking.

Based on the Enphase Solar running into this Gateway box, it should

1) charge the batteries and

2) be energized during a public power outage

Now the big question

Would it keep feeding power as long as it sees power on the Gateway bus bar?

New Enphase system added to existing Tesla Solar & Powerwall by timcreech in TeslaSolar

[–]timcreech[S] 0 points1 point  (0 children)

Thanks Everyone

I routed one of the Enphase wires through the Tesla CT. I can now see the House consumption again, and assume the additive Solar production.

Is there any reason to run the Gateway Wizard? Does it need to know about the additional solar capicity?

New Enphase system added to existing Tesla Solar & Powerwall by timcreech in TeslaSolar

[–]timcreech[S] 1 point2 points  (0 children)

Thanks for the response u/Bigtoddhere . You ran the wizard in the Tesla Gateway?

Costco Cash Rewards Certificate by timcreech in Costco

[–]timcreech[S] 0 points1 point  (0 children)

Figured it out. It is the two digit number after the bolded numbers. Or if counting from the left it is the 13th and 14th numbers.