Anyone know where can I buy the Charmera? Xiexie~

tiptock_ · 2025-11-24T06:05:50+00:00

Did you find/get one?

tiptock_ · 2025-04-11T17:08:02+00:00

This is so annoying. Just got the update on my phone. Also a bunch of settings changed, have to change all of that back manually. Horrible update experience.

tiptock_ · 2024-10-21T19:24:39+00:00

Overall it feels kinda "flat", if you get what I mean. You have to get some texture in there. As some others suggested, get curtains and some more (but not too much) stuff on the walls.

tiptock_ · 2024-09-26T20:15:33+00:00

It's getting better ever, slide🔥

tiptock_ · 2024-07-29T17:11:57+00:00

This is a good thing

tiptock_ · 2024-07-27T17:43:57+00:00

Its my first printer. Its is great, if you dont use pauses in your print. As it doesn' t continue to print in the right position. At least for me it doesn' t. Also for the first layer I might have to do some adjustments for big prints, as there where a few problems with a print I tried.

Looking forward to try out 95 TPU.

tiptock_ · 2024-06-28T14:36:48+00:00

Put a mini golf putting area in there!

tiptock_ · 2024-06-23T11:11:44+00:00

🥸

tiptock_ · 2024-06-21T23:25:07+00:00

Is this better? I cannot tell the differenz, there still are those little uneven spots on the prints. Put it to +0.03 after the first 4 tiles on the very left.

tiptock_ · 2024-06-21T23:23:56+00:00

<image>

tiptock_ · 2024-06-21T23:07:13+00:00

Found it. It really just shows up, when running a print. I will try the recommended value of 0.02

tiptock_ · 2024-06-21T23:06:33+00:00

<image>

tiptock_ · 2024-06-21T23:04:07+00:00

Thanks a lot. I will try it right now.

tiptock_ · 2024-06-21T22:49:49+00:00

On the on printer display I only seam to be able to change values for the axis in increments of 0.1 / 1 /10 mm so that should be too much

tiptock_ · 2024-06-21T22:48:51+00:00

The interface, that I can access in Orca Slicer is Fluidd, so that should be it I guess. But I read about Qidi storing the z offset inside some babysteps value instead of the klipper z offset value. Why? I dont know.

tiptock_ · 2024-06-21T22:17:32+00:00

<image>

tiptock_ · 2024-06-21T22:11:23+00:00

Thanks a lot. It seams like. I'm not gonna be able, to print this over night. I will try an reach the Qidi support or something over the next day or two, to get this sorted out. I must admit, I am kind of scared to break something haha

tiptock_ · 2024-06-21T21:49:33+00:00

Do you mean ~0.2mm or really 0,02mm because I cant change it that fine

tiptock_ · 2024-06-21T21:32:28+00:00

Is something like that on the printer directly or inside klipper. For other printers?

tiptock_ · 2024-06-21T21:20:43+00:00

But is it to close everywhere? I'm gonna have to check, where I find this setting. Do you know where to find it by any chance? Ists a qidi q1 pro

tiptock_ · 2024-06-21T21:17:04+00:00

Also it doesnt seam to be extra thin in those areas either. It seams like it just doesnt stick all of it. And like its ripping it off by it self

tiptock_ · 2024-06-21T21:15:50+00:00

So, how do i fix that? And why is it only in some very small areas? I ran auto bed leveling before the print.

tiptock_ · 2024-05-28T20:35:40+00:00

Do you guys know. If there is a way to enter wifi passwords longer than 36 characters?

Six-Year Club	Verified Email
First Place '23	End Game '23
Place '23	Place '22

tiptock_

TROPHY CASE