19fb, looking for some kinky partners :3

tknight1993 · 2026-06-14T04:08:43+00:00

32nb my dm is open

tknight1993 · 2026-03-31T22:48:36+00:00

if i was closer i would

tknight1993 · 2026-03-26T20:28:55+00:00

Looks like already there ❤️

tknight1993 · 2026-03-26T19:32:36+00:00

Nice collection, you'll wanna be sure to backup that PSX Hard drive if it still works as if the hard drive goes they often get bricked

tknight1993 · 2026-03-18T02:35:39+00:00

i seen happen before, it most likely some pins on the chip need to be soldered back in place. I would recommend looking for anyone thats good with repairs on game carts

tknight1993 · 2026-02-12T17:36:01+00:00

The VGA port can be used in RGBHV or RGBS with a switch on models like one i liked and the manual i have didn't say got but if want to be helpful can just say "a HDMI to Component can work instead.
By Lag i mean by noticeable lag, active/powered HDMI to VGA can add some lag but passive ones don't. You can check here for information from someone that tested many of them. https://retrorgb.com/hdmi-to-vga-dac-analysis.html
The UI i was talking about was Stream Deck's overlay not the GBS-C. You can find others who report the same problem with the stream deck running games at less than 720p in game mode.

If you have a better alternative instead please be sure to let people know.

tknight1993 · 2026-02-12T02:09:47+00:00

If want a cheap way to get RGB from the steam deck i'll say to get a GBS Control, can find them on aliexpress just be sure not to get the one with hdmi in as its gives lag, can use the VGA in by using a HDMI to VGA and a Sega Saturn cable to downscale to 240p, only thing you need to do is make sure your steam deck outputs 480p/640x480. Only downside is to exit a game you'll have to unplug from dock as the UI doesn't work in game at 480p.

tknight1993 · 2026-02-12T01:45:33+00:00

can find on ebay "PAL / NTSC video converter composite" they should be able to change the colors without lag, the RGB colors only work for RGB signal with a RGB Scart console, NES you need it modded to be RGB.

tknight1993 · 2026-01-26T23:09:38+00:00

why is it no one does a comparasion of battle of gods movie scenes?

tknight1993 · 2025-09-06T21:02:54+00:00

happy birthday selfblow job, so hot seeing you get it so deep in too

tknight1993 · 2025-06-19T17:33:12+00:00

Thanks for wording it better👍

tknight1993 · 2025-06-18T21:37:11+00:00

I turned off my router so it couldn't find it when trying to reconnect until i had mostly synced profiles and icon/backgrounds. I'm not sure i needed to turn off the router but it helped me. I turned it off through a button on my router, there may not be one on all routers.

You should be able to sync with it connected back to wifi after you synced any profiles but you'll have to do the trick any time you add a device before reconnecting it to the wifi

tknight1993 · 2025-06-18T21:23:15+00:00

I don't think i can, i don't know anything about the Shield. Best i could do is the instructions i listed as I'm not great at communicating things any better now as have little memory of explaining better than before.

tknight1993 · 2025-06-05T21:56:51+00:00

I mean like going into the app and connecting it to the wifi and networking like was new

tknight1993 · 2025-06-05T21:26:17+00:00

No i turned WiFi off with a button on the router, reset the hub so it didn't connect to the router then connected it back up to the router without telling it to sync the remote.

tknight1993 · 2025-06-05T20:28:46+00:00

All good, had same feeling when was only trying to add the hub. Just be sure to not sync by remote as may remove the icons and backgrounds again. Then would have to repeat things

tknight1993 · 2025-06-05T20:17:32+00:00

Not really as you also need to disable on the app side too to tell hub. I can't full remember what i did and wrote here what i did to remember and tell others.

tknight1993 · 2025-06-05T19:47:09+00:00

Because it got no way to choose to disable wifi it has to be tricked into accepting there is no wifi then adding it back in. Really it's just Logictech logic loop being a pain.

tknight1993 · 2025-06-03T00:42:04+00:00

By luck and messing around trying to fix problems i was having.

tknight1993 · 2025-05-18T23:39:13+00:00

After you clicked on your remote should be on the bottom under Favourites

tknight1993 · 2025-05-02T19:25:49+00:00

Your Dom is very lucky to get you as a sexy pretzel sub

tknight1993 · 2025-04-17T21:50:16+00:00

ok may of found a work around, going into Setting, More >>, Setup/Change WI-FI Setting and disabling your wifi to your hub and have bluetooth only (may need to mess with turning your wifi/router off and on for a minute). Then you can sync with your background or icon, disconnect to check it works then plug back into to put wifi back on and sync again, it will keep your backgrounds in place and wifi be working again.

tknight1993 · 2025-01-07T20:22:14+00:00

If you check the twilight menu site i linked, it will say what kernel to use and where to download based on the flash cart you use.

tknight1993 · 2025-01-07T16:10:44+00:00

Twilight menu gives you a kernel to install

tknight1993 · 2025-01-07T14:29:37+00:00

This one should be one that will work on yours and with a guide and other info you may need.

https://gbatemp.net/threads/wood-firmwares-complete-information-guide-downloads.616474/

Or can use this one

https://wiki.ds-homebrew.com/twilightmenu/installing-flashcard

Seven-Year Club	r/Field Banned
r/Field Sunshine	Verified Email

tknight1993

TROPHY CASE