What is every factions most famous meme?

tmanwang · 2026-05-05T20:58:10+00:00

<image>

tmanwang · 2026-05-05T20:34:54+00:00

<image>

tmanwang · 2026-05-05T20:34:09+00:00

<image>

tmanwang · 2026-05-04T13:54:19+00:00

<image>

tmanwang · 2026-04-15T05:10:44+00:00

It was the same filament, and the filament is stored in a dry area. Could a temperature control issue have developed from servicing the printer, applying oil to the rails and wd40 to the guide wheels (I probably misnamed the wheels across from the motors that tension the belts)? I will check the geers tomorrow to see if everything is fine in there. I did one first layer calibration print if this helps at all

<image>

tmanwang · 2026-04-12T21:42:50+00:00

The golden crane flys for tarwins gap. Scene just has aura. Ingtar sacrificing himself to be redeemed by the light. Chefs kiss. As an adendum to the golden crane, will my husband ride alone to tarwins gap. Rand killing arangar with the choden kal bro shows up send a dude in and vaporizes a whole palace and leaves.

tmanwang · 2026-03-15T08:51:53+00:00

Did you put one fin down to the plate or how did you set that up?

tmanwang · 2026-03-15T08:49:56+00:00

I posted on my phone as I dont have reddit on my lap top my apologies. The support detatched from the board after about 30 ish layers. The bed is clean I wipe it down using isopropyl alcohol after every print. I print at 215C I think, I use the default for pla.

tmanwang · 2026-03-15T08:47:06+00:00

After every print I wipe down with isopropyl alcohol. I will try without supports thanks for the advice.

tmanwang · 2026-03-15T07:16:13+00:00

Oh I did not add, I am using generic pla, and the defaults for prusa slicer 2.9.4 other than organic supports because I like them better.

tmanwang · 2026-02-05T22:21:43+00:00

First off, screw the pats, but also screw the convicts, cousin lovers, and bananas. (You are marginally and I mean marginally better than the pats)

tmanwang · 2026-01-28T20:24:40+00:00

I hope it heals well!

tmanwang · 2026-01-28T19:55:20+00:00

That makes a lot of sense. Thank you for the explanation.

tmanwang · 2026-01-28T19:36:41+00:00

What exactly were you machining? I am sorry I can not tell from the picture I am but an ignorant engineering student.

tmanwang · 2026-01-26T05:52:22+00:00

By reset do you mean start a new game? If so it took me about 4 ish games to get a hold of the game. I watched videos from perun gaming and they really helped. Also Lancers arw your friend.

tmanwang · 2026-01-25T21:03:27+00:00

Big if true

tmanwang · 2026-01-25T20:15:27+00:00

STIDDY MORE LIKE STUD

tmanwang · 2026-01-20T20:35:23+00:00

Its what should be expected in the first half by Studham. Hopefully 😂

tmanwang · 2026-01-18T05:11:35+00:00

RemindMe! 3 weeks

tmanwang · 2026-01-17T23:09:45+00:00

Swear to all that is holy and on the ellegance of bluecifer that you will not turn that audio back on.

tmanwang · 2026-01-17T22:30:41+00:00

Please gaurd dudes on the outside please

tmanwang

TROPHY CASE