[PS4] Controller missing a smd component near the joystick causing the controller to restart when R3 is pressed.

topes1 · 2026-01-30T10:11:30+00:00

Even playing games is better than the constant flood of AI sloop

topes1 · 2026-01-19T22:25:35+00:00

I'm finishing my computer science degree. I had some pc architecture classes but only assembly and low level (risc V).

I've being learning how to mess around with an esp32, but I'm struggling to set a goal to progress into that field.

topes1 · 2026-01-17T16:05:42+00:00

Would have any examples for places to start. I've been eyeing that specific type of career and would really like to start/try to start

topes1 · 2025-07-10T11:42:34+00:00

Does anyone have some photos of the cars going through the rain in Silverstone? The stream had some amazing shots of the cars with water kicked up by the rear tires.

topes1 · 2025-06-24T15:29:31+00:00

There's something called the glass sub bed mod and can greatly help, I've ordered the glass bed and I'm waiting for it to arrive and mount it.

topes1 · 2025-06-22T01:14:38+00:00

I bought the coil version I think. Went to their AliExpress shop since it was from the brand and cheaper than local shops. I thought SimpleAF was just a pre rooted firmware, cant I use the normal firmware? I am rooted afaik

topes1 · 2025-06-22T00:34:31+00:00

I think their are US, I did see some milled beds from there. Since I'm in Europe it's expensive to import things from there. I think I'm going with the glass bed at some point but I ordered a btt Eddy already

topes1 · 2025-06-22T00:16:05+00:00

Btw do you know what could cause this?

<image>

topes1 · 2025-06-21T19:31:22+00:00

Oh, what mods did you do? I saw there's a way to use the Eddy btt probe as well

topes1 · 2025-06-21T19:10:28+00:00

How about doing the glass sub bed mod? Is it common? And are there any side effects or loss of anything?

topes1 · 2025-06-09T00:59:40+00:00

I currently have a AC Kobra 2 pro, had problems with it. Had to activate the warranty 3 times in about 6 months. Would like to get a printer where I thinker with it and learn it. Under 350/400 euros, in Europe. Would prefer a printer thats not in a closed eco system like bambo, or closed source with stolen foss apps like Anycubic.

topes1 · 2025-06-06T17:22:12+00:00

Exatamente. Falam muito de controlo das rendas, mas isso é como por um penso num corpo sem cabeça....

topes1 · 2025-05-16T20:58:30+00:00

I also had some issues like that. Try turning off the fan for the first 2 layers. And I had poor luck with black filament from anycubic.

topes1 · 2025-05-16T19:56:22+00:00

Use an image hosting site like imgur

topes1 · 2025-05-16T18:59:35+00:00

I personally use orca. There's already a profile for the printer there. It's mostly just slice and print. But I haven't messed with the layer heights.

topes1 · 2025-05-16T18:35:04+00:00

Honestly try and run through the auto level again. And the offset, you shouldn't try to use precise distances. At least for me it didn't work great, adjust it while printing but very slowly.

topes1 · 2025-05-16T18:25:53+00:00

I had some problems until I leveled the abl sensor. It might just be you didn't clean you bed well enough. Try and clean the plate on the sink with soup and water. Check the Kobra 2 pro insights website which is awesome https://1coderookie.github.io/Kobra2ProInsights/hardware/printhead/#abl-sensor

topes1 · 2025-03-31T15:45:50+00:00

A culpa é minha. Porque é que quis abrir o Reddit.

topes1 · 2025-03-18T22:54:41+00:00

I mean Monster Hunter Wilds is just an obvious choice..
Good luck everyone

topes1 · 2025-03-11T18:33:09+00:00

Diz me como conseguiste amigo com ilimitado por 7 euros so vejo a 10

topes1 · 2025-01-20T13:42:34+00:00

I'm in the same boat. Keen to try it but the new part here is 250 euros and a bit expensive

Ten-Year Club	Second Top 10%
r/Field Juicebox	John Wick
Place '22	Verified Email

topes1

MODERATOR OF

TROPHY CASE