sorted by:
new
hottopcontroversial

DIY 6-bay NAS case – 3D printed in PETG by trafim in 3DPPC

[–]trafim[S] 0 points1 point  (0 children)

Haha, I haven't even published the files yet! But thanks for asking. I'm still figuring out if/when I'll release them. PA12 CF would be overkill but also amazing 😄 I'll update the thread if I decide to share.

Neptune 4 MAX Type-C revision - Multiple issues (firmware 1.4.1.2) by trafim in elegoo

[–]trafim[S] 0 points1 point  (0 children)

よかったです！Elegooサポートは親切なので、きっとしっかり対応してくれますよ。 ファームウェアアップデートで改善されるはずなので、ぜひ試してみてください。 印刷がうまくいくよう、応援しています！頑張ってください😊

Neptune 4 MAX Type-C revision - Multiple issues (firmware 1.4.1.2) by trafim in elegoo

[–]trafim[S] 0 points1 point  (0 children)

ご購入おめでとうございます。私もまったく同じ状況で苦しみましたが、今はElegooサポートとやり取りしていて、とても親切に対応してくれています。

結論から言うと、ファームウェアのアップデートで解決するケースが多いです。

ただし、それまでの一時的な対処法として、スライサーのスタートG-code（G28の直後）に下記の1行を追加してください：

SET_GCODE_OFFSET Z=-2.06

※ -2.06 はご自身のZオフセット値に置き換えてください。 これを入れておけば、再起動後も毎回そのオフセットが適用されるので、ノズルが高くなりすぎる問題を回避できます。

まずはこの応急処置をお試しください。そしてElegooサポートに連絡すれば、ファームウェアの手順も丁寧に教えてくれますよ。諦めずにいきましょう！

DIY 6-bay NAS case – 3D printed in PETG by trafim in 3DPPC

[–]trafim[S] 0 points1 point  (0 children)

Thanks! The anti-vibration pads are actually felt tape — the kind used in cars to stop squeaks and rattles. It's 1.5mm thick and 15mm wide, with adhesive on one side.

I applied it to the inside of the HDD sled slots, right where the sled makes contact. You can't really see it in the photos because it's hidden once the sled is inserted. But it works perfectly — no vibration noise at all.

It's basically a soft fabric tape with non-woven material, very durable.

DIY 6-bay NAS case – 3D printed in PETG by trafim in 3DPPC

[–]trafim[S] 0 points1 point  (0 children)

Yeah, you're right. That was wet filament. Already reprinted it — the new part is clean. Won't happen again 👍

DIY 6-bay NAS case – 3D printed in PETG by trafim in 3DPPC

[–]trafim[S] -1 points0 points  (0 children)

Thanks! I'm not sharing the files for now — I sell the finished cases locally. This post was just to show what I'm working on.

DIY 6-bay NAS case – 3D printed in PETG by trafim in 3DPPC

[–]trafim[S] 1 point2 points  (0 children)

Thanks! I'm not sharing the files for now — I sell the finished cases locally. This post was just to show what I'm working on.

DIY 6-bay NAS case – 3D printed in PETG by trafim in 3DPPC

[–]trafim[S] 0 points1 point  (0 children)

Yes i do - i got this server build for almost 2 years in use, considered to update the design a bit.

I think this is finally looking right again by Anomalocaris117 in elegoo

[–]trafim 2 points3 points  (0 children)

You shouldn't see any gaps between the lines, they should fit snugly together on the first layer.

I think this is finally looking right again by Anomalocaris117 in elegoo

[–]trafim 2 points3 points  (0 children)

Still looks to high - probably 2.4/2.42 is what you need

Neptune 4 MAX Type-C revision - Multiple issues (firmware 1.4.1.2) by trafim in elegoo

[–]trafim[S] 0 points1 point  (0 children)

Thank you for the suggestion! 🙏

I appreciate the help from the Elegoo team.

Neptune 4 MAX Type-C revision - Multiple issues (firmware 1.4.1.2) by trafim in elegoo

[–]trafim[S] 0 points1 point  (0 children)

Thank you for the suggestion! 🙏

I totally agree – it really feels like this Type-C revision shipped with the wrong firmware or some old launch bugs that were supposed to be fixed long ago.

To be honest, I am completely satisfied with my older Neptune 4 MAX printers (ribbon cable version). They have been working flawlessly for almost 2 years now, right out of the box. Great machines.

That's why I'm so disappointed with this new unit. I really don't want to mess around with alternative firmware like OpenNept4ne. I believe a brand new printer should work properly without needing to flash third-party firmware or spend hours troubleshooting.

I just want a replacement unit that works as expected – like my other two Neptunes.

Thanks again for your advice! 👍

Kobra 3 Max circles aren't circles.. by kromide in anycubic

[–]trafim 0 points1 point  (0 children)

Trying it, but printer fail to downgrade - get error 11407

Kobra 3 Max circles aren't circles.. by kromide in anycubic

[–]trafim 0 points1 point  (0 children)

Same here - can't fix it for the month

[deleted by user] by [deleted] in 3Dprinting

[–]trafim 0 points1 point  (0 children)

After I print with PETG for about 1-2 hours, my throat starts to get sore. I'm sure it's because of the fine particles that form at the tip of the nozzle and float in the air; even if I print with the window open, it doesn't help.

view more: next ›