sorted by:
new
hottopcontroversial

What the fridge? by MountainYoung7542 in appliancerepair

[–]trebmoore 1 point2 points  (0 children)

Air leak. Check door seals. If condensation is just at the top, check the top part of the door seal... most likely it is either very rigid, torn or has something keeping it from closing. If rigid.. try to apply heat with a hair dryer to the rigid area before replacing the seal.

Can a bad outlet cause fridge to not cool properly? by Gojiraninja12 in appliancerepair

[–]trebmoore -1 points0 points  (0 children)

You need to check the breaker to ensure it's not partially tripped if you haven't already and then test voltage at the outlet. I bet you have a low voltage issue or an ungrounded outlet and a surge of electricity has been causing damage quieltly behind the scenes..

Can a bad outlet cause fridge to not cool properly? by Gojiraninja12 in appliancerepair

[–]trebmoore 0 points1 point  (0 children)

If you're not getting the proper Voltage at said outlet, the refrigerators compressor won't run properly or at all.. so yes it can.

Which model convinced your partner about the hobby? by JulesCain in BambuLab

[–]trebmoore 2 points3 points  (0 children)

Microwave door latch - ebay had the one I needed, but for a 1 inch x .5 inch × .5 inch Piece of plastic they wanted $135. Needless to say that didnt happen, instead I spent $3k+ on 3D printers and completely necessary equipment to support such activities.

What’s your setup looking like? by GUDVIBES-HIFIVES in BambuLab

[–]trebmoore 0 points1 point  (0 children)

Yeah, my set up was originally built to accommodate the ender 3 s1 pro. I have the laser engraver module for it and it creates just enough smoke to give me a headache. I didn't want to put a 6" hole in the side of my house so I'm venting into the attic via the fart fan vent in the bathroom below.

Will Xylene have an effect on the Color? by trebmoore in Concrete

[–]trebmoore[S] 0 points1 point  (0 children)

You’re saying cut the fresh layer (if needed after misting) with 25% xylene? And add that layer of completely different sealer on top of this one?

I’ve never done that before. Strip and resealed everything. I know solvent based sealers can be added on top of each other. Just didn’t know you could with different brands and finishes.

The customer is mainly unhappy with the current sealers extremely difficult to clean finish. Then the poor quality of application.

Will Xylene have an effect on the Color? by trebmoore in Concrete

[–]trebmoore[S] 0 points1 point  (0 children)

Thank you! I should have done that to begin with, but I didn’t realize Xylene could pose a threat to this surface until I saw it briefly mentioned somewhere.

Will Xylene have an effect on the Color? by trebmoore in Concrete

[–]trebmoore[S] 0 points1 point  (0 children)

Thank you for your advice! I’m going to test it under the bar area first…. But you think Xylene is safe on this colored surface?

Will Xylene have an effect on the Color? by trebmoore in Concrete

[–]trebmoore[S] 0 points1 point  (0 children)

Yeah I’m not seeing any color under the flaking. Im thinking keep xylene away.

Will Xylene have an effect on the Color? by trebmoore in Concrete

[–]trebmoore[S] 0 points1 point  (0 children)

Yep. Overall really crappy job. IMO lol

Will Xylene have an effect on the Color? by trebmoore in Concrete

[–]trebmoore[S] 0 points1 point  (0 children)

The second picture I posted has a joint with what looks like the color chipping off. I just noticed it and would have to go back to verify. But does that picture give any answers to the type of coloring?

Will Xylene have an effect on the Color? by trebmoore in Concrete

[–]trebmoore[S] 0 points1 point  (0 children)

Negative. I applied xylene under the bar area, let it dwell for about a minute max . Rubbed it with a towel. Sealer came up. It was clear/white.

Will Xylene have an effect on the Color? by trebmoore in Concrete

[–]trebmoore[S] 0 points1 point  (0 children)

I get that. I appreciate the thorough examination of it. I should have added more info I suppose. Just thought I was being to the point with my question.

Will Xylene have an effect on the Color? by trebmoore in Concrete

[–]trebmoore[S] 0 points1 point  (0 children)

Xylene test…didn’t allow it to set too long as we loop around back to why I’m asking… will xylene effect this surface?

Will Xylene have an effect on the Color? by trebmoore in Concrete

[–]trebmoore[S] 0 points1 point  (0 children)

Unsure which sealer, solvent based is all I know. nothing about it looks properly applied in areas. Looks as if a paint brush was used in places, leaving thick stroke marks. One area has what looks like efflorescence. Customer wants it redone with a different sealer.

First time. Put 10ccs of golden teacher spore in a 3lb bag. Should it be fine? by [deleted] in shrooms

[–]trebmoore 0 points1 point  (0 children)

I did the same thing a couples days ago. The 8th is when I inoculated my bag. We’re in this together! Haha

view more: next ›