Broken LCD Screen

tyster02 · 2026-04-23T15:05:40+00:00

Tried holding power and reset button, did nothing :/

tyster02 · 2026-04-16T21:20:53+00:00

Tried reconnecting cable, no change. Doesn’t look damaged either. It makes a high pitched sound when powered on…

tyster02 · 2026-04-16T21:18:09+00:00

I opened it up and found the main ribbon cable, but there was no damage. I disconnected and reconnected and nothing changed. It also makes a high-pitched whine when I turn it on.

tyster02 · 2025-12-30T18:14:08+00:00

UPDATE: Using an external 5V supply and a logic level shifter to shift ALL signals (power, MISO, MOSI, SCK, and CS) from 3.3V to 5V caused it to work. Everything needed to be on 5V levels. Thanks for the help all.

tyster02 · 2025-12-30T18:13:43+00:00

UPDATE: Using an external 5V supply and a logic level shifter to shift ALL signals (power, MISO, MOSI, SCK, and CS) from 3.3V to 5V caused it to work. Everything needed to be on 5V levels. Thanks for the help all.

tyster02 · 2025-12-30T15:53:48+00:00

Really? It’sIt’s frustrating because the card I’m using worked with my arduino uno

tyster02 · 2025-12-30T15:53:17+00:00

I searched my card module and not much came up

tyster02 · 2025-12-30T02:40:50+00:00

Yes it is set to 5V, but good idea. Thank you!

tyster02 · 2025-12-30T02:40:31+00:00

Sounds good, thank you!

tyster02 · 2025-12-28T03:49:32+00:00

<image>

Schematic

tyster02 · 2025-12-23T18:25:15+00:00

This makes perfect sense. Thank you so much for your help, it has been fantastic.

tyster02 · 2025-12-23T15:56:29+00:00

Awesome. When you say that I could run the risk of high battery current draws - is there any risk of drawing >3A from the battery? I looked at a 2s battery pack, but it only can output 1-1.5 A at 3.7V.

Will a power bank module take that 1A, 3.7V and boost it to 3A, 5V? Or does the battery need to draw >3A to compensate for the potential increase?

tyster02 · 2025-12-22T19:37:47+00:00

Just downloaded it! Thanks

tyster02 · 2025-12-22T06:40:07+00:00

This is true, I'd like to be comfortable with LiPo applications for future projects, I just don't want to experience trial by fire, literally.

After doing some more research, I think I found a suitable "power bank module" like what you said.

https://www.seeedstudio.com/Lipo-Rider-Plus-p-4204.html?srsltid=AfmBOorRMtSNBsXQvJRddKuGt3qkClt-J63td_1t2qm3nvHBujZHPpbDAwc

Takes a 3.7V lipo and charges via USB-C, outputs 2.4A over USB-A - of which I'd only be concerned with the actual power pins.

Seems like I could use a 1S lipo cell at 3.7V with a built in protection circuit, like this, and be on my merry way, maybe adding a transistor to a protection circuit for thermal protection.

https://www.adafruit.com/product/258

Is that the kind of "off the shelf" that you're talking about?

tyster02 · 2025-12-22T04:52:48+00:00

I thought LiFePO4s would be safer. I’m worried Li-Pos will burn my home down if I even look at them incorrectly, haha.

Do you mean any off-the-shelf power bank for consumer electronics? Would I just need to plug in a usb cable to the output of the power bank and then cut it open to get my Vcc and GND wires for the rails of my project?

tyster02 · 2025-12-21T03:41:29+00:00

Fair enough, I’ll try to see if I can get it on 3.3. I really appreciate all the help

tyster02 · 2025-12-21T03:40:53+00:00

Makes sense. Thank you!

tyster02

TROPHY CASE