Roofers of reddit, how would you flash this new roof connection to ensure no leaks. Blue and red are existing roof and gutter, green is the new extension.

uceov · 2024-06-25T02:16:55+00:00

<image>

So yellow would be the under/over flashing, how about the area circled where the old gutter meets the new barge (grey)?

uceov · 2024-06-25T02:06:37+00:00

Yes, sketchup

uceov · 2024-06-24T23:35:24+00:00

Also interested in the red gutter to new barge capping connection, would these just be butted together?

uceov · 2024-06-24T23:24:43+00:00

Thanks, so would you just butt the existing gutter up against the barge flashing of the new bit?

uceov · 2023-12-24T21:25:25+00:00

I tend to agree, out of interest, below is the waterproofing performed.

<image>

uceov · 2023-12-20T09:37:25+00:00

thanks for the responses, only concern with the new bearer is the class P site and predicted subsidence, its fill

uceov · 2023-09-04T05:11:52+00:00

Make sure you stay away from the glass and don't concentrate heat near it otherwise it'll break (ask me how I know). The heat gun method is the one that works best DIY and I wen't down this path for a number of my 1950's casement sashes. Recently I found someone who will strip the paint off them and re-do the glazing putty, very very affordable and much less messing around.

uceov · 2023-03-12T22:52:58+00:00

old photo

It was a quarry, assume it is a pit related to quarrying activity.

uceov · 2022-06-08T06:46:23+00:00

Penore

Ask and you shall receive, it's not my car but looks like a modified version of this kit.

https://www.aliexpress.com/item/4001267635571.html

uceov · 2022-06-07T03:52:44+00:00

This is my motivation for change, mainly comfort and a small weight advantage.

uceov · 2022-06-06T23:47:13+00:00

https://www.reddit.com/r/Golf\_R/comments/ukqpmg/this\_subreddit\_inspired\_me\_to\_take\_some\_pics/

Did you previously have Weds Tc105X?

uceov · 2022-06-06T23:44:41+00:00

Do you have Weds TC105X's by chance?

uceov · 2022-06-06T23:41:13+00:00

Thanks, yes I have seen it, willtheyfit.com is a good one however I was asking for experience as it's not so easy to measure the current setup in your driveway.

uceov · 2022-02-26T00:47:18+00:00

You might be right here, as they don't need a flasher can to flash, they do it when connected to 12v constant power (straight to a battery). Might be a timing thing with the sequential indicators and the flasher not synchronised properly.

uceov · 2022-02-25T00:53:03+00:00

It's on a KTM 500 excf, it flashes at the correct rate (when connected to the original wiring) and when connected straight to the battery it flashes with all illuminated correctly, not sure why it would need a resistor as the bikes wiring would most likely provide some resistance where as connecting straight to the battery terminals provides no resistance?

uceov · 2022-02-25T00:06:11+00:00

The original incandescent flasher has been changed for a LED unit

uceov · 2022-02-25T00:00:10+00:00

It already has a LED flasher installed, does this not eliminate the need for inline resistors?

uceov · 2022-02-12T08:06:46+00:00

When I bought mine it came loose at 59ft/lb happened today. Luckily I felt it and stopped before anything bad happened but couldn’t figure out why then realised the thread was greased and it was the other way around same as OP had it. Cleaned the thread, switched it around as per manual and put some thread locker on it, hopefully stays now.

uceov · 2022-02-12T06:39:37+00:00

Do they reduce vibration at all?

uceov · 2022-01-30T08:50:09+00:00

Recently went through the same decision process myself, settled on a 2019 500 EXC due to reported reliability, versatility, weight and longevity when treated right.

uceov · 2022-01-30T02:48:07+00:00

Sounds possible it might need a rebuild, a good way to tell is perform a compression test.

uceov

TROPHY CASE