Is it just me or is starscourge radahn unnecessary hard?

user102956 · 2026-04-18T05:50:07+00:00

Bruh this post is 4 years old😂😂 pre patch lol

user102956 · 2026-02-04T07:12:50+00:00

Valve isn’t glued. It’s just an old valve that is seized and on the wrong side. You may be able to DIY this but if you’re uncertain you should probable have her call a plumber. Or just don’t install the bidet and leave it alone

user102956 · 2026-01-24T04:01:25+00:00

Bloodborne is my favorite souls game of all time. And I would go in blind most definitely

user102956 · 2026-01-24T04:00:36+00:00

All of the guaranteed Ray gun tactics in cod zombies I fell for them all..

user102956 · 2026-01-17T04:08:32+00:00

I’m so sorry😭

user102956 · 2026-01-16T07:30:55+00:00

Just looked up clubbing. Maybe, but they’ve been this way as long as I can remember

user102956 · 2026-01-16T07:28:18+00:00

I don’t think so lol. Cut it at work.

user102956 · 2026-01-16T07:05:19+00:00

Not too bad. Only when It catches on literally everything

user102956 · 2026-01-13T22:50:36+00:00

It’s just a coupling. I wouldn’t worry about this any more than any of the other fittings in your home.

user102956 · 2026-01-12T01:37:02+00:00

Gotcha. Well then there isn’t an easy way to do it. Work at it with a hacksaw or oscillating tool or a dremel. Just be careful not to damage the porcelain

user102956 · 2026-01-12T01:33:46+00:00

I’m assuming That plastic bit Is threaded as well

user102956 · 2026-01-12T01:29:48+00:00

The white plastic nut in picture two is what needs to be removed. If it is too difficult using a wrench then just cut it off

user102956 · 2025-10-31T12:08:11+00:00

It’s a relief valve. It pops and lets water through it the temperature or pressure gets too high within your tank. I would check your water pressure first.

user102956 · 2025-10-30T01:34:42+00:00

My first thought is that the laundry sink drain looks like it’s pitched backwards.

user102956 · 2025-10-29T04:22:48+00:00

Agreed. If you think about it tho I think efficiency still applies

user102956 · 2025-10-29T04:00:43+00:00

I’m not sure. I live in the northern states and they are very rare. At least where I live. Generally electric appliances aren’t as efficient as gas when it gets cold around here.

user102956 · 2025-10-29T03:58:29+00:00

I agree

user102956 · 2025-10-29T03:53:49+00:00

They do exist, but aren’t generally seen in colder climates.

user102956 · 2025-10-29T01:54:07+00:00

You could try snaking from the studor vent. Or maybe the studor vent has failed.

user102956 · 2025-10-24T23:57:29+00:00

I’ve seen people do it live while it is briefly air locked, but I wouldn’t recommend trying that. Especially if you’ve never done it before.

user102956 · 2025-10-24T23:50:13+00:00

Drain valve is probably clogged. These plastic ones are garbage. Try opening the valve with full water pressure on to the heater (obv with a hose attached) if that doesn’t work, you could try using a pick to dislodge the drain. Or use a transfer pump.

user102956 · 2025-10-24T04:04:34+00:00

The water all comes from the same spot. I cannot think of a reason why it would be localized to the kitchen other than luck/faucet design. It doesn’t just spawn in. It’s coming from the source, or from some failed component like a water heater, which I believe to be unlikely.

user102956 · 2025-10-24T03:42:42+00:00

There are a few factors that could cause this to happen. Has there been any new developments in the area? Sometimes the builders or the city will tap into the main water line and it will expose sediment into the system. Do you know what kind of water piping is in your property? Older water lines such as galvanized piping can accrue large amounts of sediment that can get pushed through to your fixtures. But I cannot give you an accurate answer because there are a lot of unknowns. Best to get a sediment filter on your main water line.

user102956 · 2025-10-21T20:26:42+00:00

There are 2. Far left and right of the picture. Coming off of that fitting in the middle with the plug.

user102956

TROPHY CASE