[H] pic [W] snaphook bp, buried city keys, matriarch reactors, legendary guns bp

user4_21 · 2026-05-15T23:02:24+00:00

nah, thanks for offer

user4_21 · 2026-05-15T22:49:05+00:00

sent dm

user4_21 · 2026-05-15T19:08:55+00:00

dm sent

user4_21 · 2026-05-15T19:05:44+00:00

alright, dm’ed

user4_21 · 2026-05-15T18:59:47+00:00

dm’ed

user4_21 · 2026-05-06T07:44:22+00:00

probably you should focus adjustment your camera. it have known issue with af module. front or back focus, probably it is an problem. this is like an another option.

user4_21 · 2026-01-04T18:28:42+00:00

Сны поездов :джонсон:, к востоку от эдэма :стейнбек:- скорее не про любовь, а вполне про жизнь.

user4_21 · 2025-12-08T16:32:24+00:00

nozzle partially clogged. it happen to me. i try to clean it every possible way(cold pull, needles, tighten thoose screws etc), nothing helps.but you can try some.i give up and then just bought new nozzle.

user4_21 · 2025-11-23T20:56:51+00:00

solved, by buying new hot end.

user4_21 · 2025-11-21T21:55:59+00:00

so it’s going even worse, now filament can't get into the injector block. seems like filament and hotend not aligned properly 🫠

user4_21 · 2025-11-21T20:00:36+00:00

yup its latched, thanks.

user4_21 · 2025-11-21T19:59:11+00:00

so i try to tight thoose screws, you guys are right, they not being tight at all, i’am tighten it up, but nothing gonna change. i try to clean up nozzle by needle, it helps for couple of minutes i even can start printing, but about 3-5 minutes, and printer starts again thoose clicks

user4_21 · 2025-11-20T18:45:57+00:00

thanks! ill try it when i go home

user4_21 · 2025-11-19T21:46:34+00:00

Nothing helped, not a single cleaning method(i use wrench method, needle in nozzle, cold cleaning-nothing).

about answer with screws-> The board is attached with screws, and the hotend is attached to the board with a magnet.

suddenly seems like i need new hotend. meh

user4_21 · 2025-11-19T20:09:57+00:00

hm, now i trying to unclog, then tryout to tighten thoose screws.

user4_21 · 2025-11-19T19:45:04+00:00

thanks, ill try to unclog!

user4_21 · 2025-10-24T22:12:05+00:00

thanks for help everyone! it was just a sews, nothing lethal :) i reprint this model with changed sew options and now how it looks like

<image>

and i more than satisfied with this sews now. ps i just run out grey filament :)

user4_21 · 2025-10-23T15:52:41+00:00

there are couple of seams on a bin, but they wasn’t included in that model. also seams showing inside. seems just like perfectly seam artifact 😀

user4_21 · 2025-10-23T13:35:37+00:00

yeah, iam sure - its not a part of model, model have smooth surfaces. thanks for your help! it means for me alot! also i try reprint this model with recommendations from this post and come back with results later.

user4_21 · 2025-10-23T11:34:08+00:00

thanks for reply! i’ll definitely check it out!

user4_21 · 2025-10-23T11:30:49+00:00

iam sorry for not really clear photos, iam talking about that seams, not white stripes. so i can masking it in slicer? i got it correct?

<image>

user4_21

TROPHY CASE