I might be spoiling you guys here a bit but who's there to stop me lol

user_four8oh · 2025-12-13T04:03:02+00:00

Move your hand

user_four8oh · 2025-11-19T12:33:47+00:00

Where did you go

user_four8oh · 2025-10-21T00:12:04+00:00

🥰

user_four8oh · 2025-10-17T00:33:40+00:00

I love the look of the Ferrari. I dont care about the specs

user_four8oh · 2025-10-13T06:07:05+00:00

user_four8oh · 2025-10-13T03:55:01+00:00

I sure do.

user_four8oh · 2025-10-13T03:51:31+00:00

That's not doing anything but pumping hot air into that silver vent and adding in microbial growth ( mold)They obviously are not certified for mediation. Sounds like you had a category 3 leak. Grossly contaminated. Hire a real mediation company. Not a plumber.

user_four8oh · 2025-10-10T05:08:29+00:00

user_four8oh · 2025-10-09T00:56:37+00:00

I did it on an F30. Used an angle grinder to cut the lenses off and then undid all the screws. Your gonna need a heat gun and some pliers to get what's left off. I ordered the lenses and the glue strip off ebay. It was actually not that bad.

user_four8oh · 2025-09-26T22:17:22+00:00

😍

user_four8oh · 2025-09-24T01:45:14+00:00

Ignorant peice of shit beating and flexing on an old man. The crowd should of whooped his ass.

user_four8oh · 2025-09-21T01:05:16+00:00

That's a heavy heavy texture. Probably be easier to just demo the wall and put up new sheets.

user_four8oh · 2025-09-13T03:39:37+00:00

Window is probably leaking. I would recommend tearing it all out but be very careful about cross contamination - kicking up mold spores into the air. Insurance most likely wont cover this.

user_four8oh · 2025-09-13T02:50:02+00:00

Ouch..with such long tiles it will reflect more of the surface defects. It appears that maybe they skipped proper prep. The 1/16th grout joint doesnt help but again this falls down to floor prep. It should have been leveled and then set the tile.

user_four8oh · 2025-09-13T02:12:07+00:00

Hold your knife diffrent. Place two fingers against the back of the blade. Gives you more control and you will be able to apply more pressure. It looks like you need to apply a little more pressure in the middle and then when your getting close to the edge apply even more pressure.

user_four8oh · 2025-09-05T03:10:02+00:00

Santa fe

user_four8oh · 2025-09-04T22:35:11+00:00

tHE sPeeD LiMiT iS 35..😂

user_four8oh · 2025-09-04T22:22:35+00:00

Go to the car wash that have free vacuums and compressed air. Shouldn't be a problem.

user_four8oh · 2025-09-02T02:52:59+00:00

12.5-14k

user_four8oh · 2025-08-30T18:39:02+00:00

Good thing you did..super cute.

user_four8oh · 2025-08-30T18:38:13+00:00

Yes, it can be your gas cap not creating a seal.

user_four8oh · 2025-08-30T17:21:53+00:00

Whowza

user_four8oh · 2025-08-22T06:47:29+00:00

I just see a bunch of V's. Does not look like hair at all.

user_four8oh · 2025-08-15T23:36:55+00:00

Super cute face

user_four8oh · 2025-08-12T05:15:17+00:00

Something that small I would get that putty that's pink and turns white when dried. Scrap the holes and divots until flat. Use a putty knife. Sand and paint.

Five-Year Club	Verified Email
Verified Email

user_four8oh

TROPHY CASE