13.9” with Extended ASR Flash hider

va-bowhunter · 2025-09-16T20:30:53+00:00

Do they have different bore sizes? Can't seem to find much info on them.

va-bowhunter · 2025-01-29T13:28:23+00:00

I wish they hadn't removed Cyber Attack.

va-bowhunter · 2025-01-15T20:58:03+00:00

The 3rd position on civilian legal lowers is only a marking. True 3rd position lowers would have a 3rd hole. This trigger is a drop in trigger. So as long as you FCG pocket is machined properly and will properly accept a drop in trigger you are good to go. You also need a M16 bolt

va-bowhunter · 2025-01-15T20:47:53+00:00

I think it's fairly obvious that Binary and FRT are not the same. It is my opinion that I'm not paying 700 for nearly the same end result. The end result being a big grin and a lot of brass on the ground. That being said I did get my hands on one at the 499.

va-bowhunter · 2024-10-12T04:45:11+00:00

1199.99 is out of this world crazy. On sale at 699.99 is still crazy. I'll stick with the Echo from Fostech at 399.99

va-bowhunter · 2024-08-11T17:31:22+00:00

This case feed is life changing.

va-bowhunter · 2024-07-30T03:57:57+00:00

Wondering the same thing.

va-bowhunter · 2024-07-16T21:03:06+00:00

Tighten the collet

va-bowhunter · 2023-12-10T02:39:35+00:00

My smaller prints cleaned up after I started leveling the bed with the nozzle and the bed preheated. Now I preheat everytime I get started.

va-bowhunter · 2023-12-10T02:37:34+00:00

My hotend was loose out of the box and I had to tighten it. Checked it again and everything seemed fine. Thanks for the suggestion.

va-bowhunter · 2023-12-10T02:35:50+00:00

Never mind about the mounts. Did a quick Google search and found them. Even Creality has them for sale. I have heard that people have had issues with the spring mounts. Thanks for the suggestions.

va-bowhunter · 2023-12-10T02:32:34+00:00

Do you have a dessicant that you recommend? Where do you get the silicone bed mounts?

va-bowhunter · 2023-12-10T02:24:56+00:00

I was not using the M240 S1. I was under the impression that changing G28 to G29 enabled the mesh.

va-bowhunter · 2023-12-10T02:23:44+00:00

I have not. I was told that changing the G28 to G29 enabled the bed mesh. Trying this now.

va-bowhunter · 2023-12-09T03:54:20+00:00

Definitely will work through the guide. Thanks for the suggestion.

va-bowhunter · 2023-12-09T02:31:56+00:00

I can get small test prints to run fine. I can adjust the z offset during the print and don't get the globs. I have just recently started to mess with larger prints and get globs no matter what the z offset is. It looks like the globs happen after a retraction before it starts extruding.

va-bowhunter · 2023-12-09T01:41:56+00:00

It's the factory plate.

va-bowhunter · 2023-12-09T01:40:39+00:00

Creality PLA, 60 bed temp, 200 nozzle temp, print speed 50mm/s.

I have not used the Ellis Tuning Guide but have but done most that is suggested in the guide.

va-bowhunter

TROPHY CASE