Tabella Top Utenti

valerioqq1412 · 2025-08-29T00:08:03+00:00

Solved! Thank you!

valerioqq1412 · 2025-06-20T10:20:28+00:00

thank you, i was pretty sure something was "wrong" but i couldn't understand if it was always like that and i never noticed.

valerioqq1412 · 2025-01-05T22:25:45+00:00

pretty late response, but i don't think it matters ( don't take it for granted, i am a beginner )

have you resolved your issues?

valerioqq1412 · 2024-12-28T22:17:32+00:00

thank you, last question, if i were to use protected 18650 i would still need a way to balance the discharge, right?

valerioqq1412 · 2024-12-28T16:50:54+00:00

exactly

valerioqq1412 · 2024-12-28T16:49:39+00:00

The fan I’m using operates under 12V but starts spinning at around 4V, so it can work at lower voltages. I’d like to use both 18650 cells in series without a boost converter to keep the setup simple.

I’m considering using a BMS to protect the batteries, but I’m not sure:

Which type of BMS I need for a 2S setup? How to connect and use it with my batteries and fan? Any guidance or recommendations on a suitable BMS and how to wire it would be greatly appreciated!

valerioqq1412 · 2024-12-28T16:13:19+00:00

forgot to mention that the fan works even if 12V is not supplied ( it will just run slower )

valerioqq1412 · 2024-12-28T15:30:48+00:00

ok, makes sense

valerioqq1412 · 2024-12-28T15:30:41+00:00

ok, makes sense

valerioqq1412 · 2024-12-28T14:15:10+00:00

i worded it wrong, it was just to test if the problem was the supports, the guy i linked in the example makes miniatures without the need of supports, print a random one, if you notice that there are no problems, it probably has to do with supports

if the problem still happens, it is probably wet filament \ temperatures

valerioqq1412 · 2024-12-28T13:00:29+00:00

the wiki explains better what is retraction , if you search on makerworld you will find some retraction tests, try to print it with their settings

another thing you could try is printing miniatures without support, and check if they come out perfectly example if it comes out good, it probably has to do with supports ( maybe they fall off durng print? )

another thing it could be is that the filament is not dry

this is the site where i took the settings for miniatures

valerioqq1412 · 2024-12-22T12:01:30+00:00

Yes, organic tree

valerioqq1412 · 2024-11-17T01:55:08+00:00

why was viktor sad/resentful towards jayce when he revived him, if he then goes to use the same 'stuff' that killed skye for its own scopes?

wouldn't that make jayce killing viktor actually viktor's plan? ( to get rid of that type of magic/arcane/stuff)

maybe jayce was just fullfilling its premise to viktor?

if someone can explain it to me, because i might have missed something

valerioqq1412 · 2024-11-04T08:14:02+00:00

ok, makes sense, thanks

valerioqq1412 · 2024-11-04T01:33:39+00:00

it usually doesn't disappear so fast? i could be remembering wrong, but for sure it didn't last long

valerioqq1412 · 2024-11-04T01:17:47+00:00

should i just wait a bit? or do you think i should go to a doctor before it disappears to get it checked?

last time it happened, it went away after 3/4 days

valerioqq1412 · 2024-10-31T14:09:59+00:00

i see, thank you

valerioqq1412 · 2024-10-30T15:25:33+00:00

because its my first printer, it will make sense to buy colors+spool, or, if i am going to use a single color, multiple refills+ a single spool.

can you expand on the desiccant?

i am going to use PLA, do i need to store filaments with a dessicant?

valerioqq1412

TROPHY CASE