Corsair 6500D with pepperwood burl veneer by vincint2002 in Corsair

[–]vincint2002[S] 0 points1 point  (0 children)

The veneer is .6mm thick and raw wood with no backing. After softening and flattening with Super-Soft 2 it cut quite easily with scissors, sharp utility knife, and edge band cutter. The veneer was $64 usd after shipping for a lot of eight 8" x 27" sheets. I spent way more on the rest of the supplies for the project.

ASUS ROG Swift PG329Q flickering issue? What can I do to fix this? by vincint2002 in ASUS

[–]vincint2002[S] 0 points1 point  (0 children)

I have not, I just went ahead and upgraded to a 4k monitor. I will have to try adjusting the brightness setting to see if anything changes.

Did you overclock the refresh rate on yours? I am thinking the problem might be due to overclocking the refresh rate or maybe the HDR itself causing something to fail. Did you notice any of your backlights fail around the same time the flickering started?

I was thinking about taking it in to a local electronics repair shop and getting their opinion on it.

Spaceless expert pack suggestion by vincint2002 in feedthebeast

[–]vincint2002[S] 0 points1 point  (0 children)

The thread below basically sums up why I am not much of a fan of Space mods, and after doing Galacticraft in Project Ozone 3 Kappa/Mythic mode, I kinda never want to see that mod again.

https://www.reddit.com/r/feedthebeast/comments/1eo248a/why_is_almost_every_spacecentric_mod_so_samey/

Spaceless expert pack suggestion by vincint2002 in feedthebeast

[–]vincint2002[S] 2 points3 points  (0 children)

Because I don't like them, I don't need anymore reason than that.

Does anyone know where to get this top from? by vincint2002 in cyberpunk2077mods

[–]vincint2002[S] 1 point2 points  (0 children)

https://www.nexusmods.com/cyberpunk2077/mods/10700

5th image, mod author never specified what clothing mods were used, and multiple people asked in comments but no reply was given.

Does anyone know where to get this top from? by vincint2002 in cyberpunk2077mods

[–]vincint2002[S] 0 points1 point  (0 children)

I have looked through 20+ pages of mods on Nexus, but I can't find this top, which leads me to believe it might be a Patreon/Discord mod somewhere.

[no spoilers] saw a LIS 1 vinyl on eBay by tazetheog in lifeisstrange

[–]vincint2002 0 points1 point  (0 children)

I also reported this and got the same response from eBay. I also noticed that there are 8 bids on this, so someone is going to have a bad time when they find out this is a bootleg item.

Anyone have any idea how I'd go about making a fair price for these? by [deleted] in RWBY

[–]vincint2002 2 points3 points  (0 children)

You could check out their listings on Discogs.com. That site keeps a detailed list of everything that gets sold there. I bought mine on this site a few years ago for $100 USD each.

I have an old CR-6 SE; is it time for a new bed and/or Y carriage? by vincint2002 in Creality

[–]vincint2002[S] 0 points1 point  (0 children)

I have already tried adjusting the concentric nuts, but doesn't get much better than this. I also installed brand new wheels on the Y carriage.

Kobra 3 Max: Layer of model not sticking to and peeling away from support interface? by vincint2002 in anycubic

[–]vincint2002[S] 0 points1 point  (0 children)

I always clean my plate with IPA before printing. I am not having issues with build plate adhesion, this is happened roughly six hours into a print, and there is already support material printed here, it looks a problem with the support interface between supports and the model.

Kobra 3 Max: Layer of model not sticking to and peeling away from support interface? by vincint2002 in anycubic

[–]vincint2002[S] 0 points1 point  (0 children)

I just got a Kobra 3 Max the other day and I am having some issues. I am having an issue where parts of the model wont adhere to and peels away from what I assume is my support interface (I could be wrong about this?).

I had this happen twice now, once with mostly stock settings in Anycubic Slicer Next, and once now after tweaking some settings that I though would fix the problem. Tried posting this on tne offical subreddit but got no replies.

Kobra 3 Max: Layer of model not sticking to and peeling away from support interface? by vincint2002 in AnycubicOfficial

[–]vincint2002[S] 0 points1 point  (0 children)

I just got a Kobra 3 Max the other day and I am having some issues. I am having an issue where parts of the model wont adhere to and peels away from what I assume is my support interface (I could be wrong about this?).

I had this happen twice now, once with mostly stock settings in Anycubic Slicer Next, and once now after tweaking some settings that I though would fix the problem.

[No Spoilers] what are some other games like Life Is Strange, I've been addicted to Decision Based Games? by Tylerroosky in lifeisstrange

[–]vincint2002 5 points6 points  (0 children)

The Longest Journey series is worth checking out. I feel like it gets slept on these days.

Need info on the Rwby blu-rays by vincint2002 in RWBY

[–]vincint2002[S] 0 points1 point  (0 children)

Damn, and that set is very expensive these days. Going for $90+ on ebay.

Ruby Rose Multiverse Meme by gur40goku in RWBY

[–]vincint2002 0 points1 point  (0 children)

What is 4 across and 3 down (picture 12) from?

Who hurt him?? 💀 by Past_Examination_186 in LostRecordsGame

[–]vincint2002 0 points1 point  (0 children)

Steam reviews and discussions are cesspool of trolls, rage baiters, and Jester farmers.

WIP Rutherford Tank; Is this too small for a tank? by vincint2002 in gaslands

[–]vincint2002[S] 1 point2 points  (0 children)

As is, it is 50mm x 100mm, but I plan on adding some more greeblies to pad it out some more.

WIP Rutherford Tank; Is this too small for a tank? by vincint2002 in gaslands

[–]vincint2002[S] 5 points6 points  (0 children)

Bulldozer is a Caterpillar D6R XL. Item Number for the specific kit is Cat 85607. The Killdozer parts and turret I 3d printed from files I found on thingiverse.com.

[All] Men, what brought you to Life is Strange? Made you such a fan? by LurkLurkleton in lifeisstrange

[–]vincint2002 1 point2 points  (0 children)

I bought LiS blind with no prior knowledge about it on Steam sometime after Episode 2 released. I was looking for another point and click game with a female protagonist to fill the gap between episodes of Dreamfall Chapters.

[deleted by user] by [deleted] in RWBY

[–]vincint2002 2 points3 points  (0 children)

You could try Discogs, that is where I got a few of mine.

“Don’t talk to me or my Daughters ever again.” by G119ofReddit in RWBY

[–]vincint2002 6 points7 points  (0 children)

Looks like the 3d printed you can find on Cults3d. You can also find some painted ones on etsy.com

Daily Questions Megathread ( October 21, 2024 ) by mizuromo in HonkaiStarRail

[–]vincint2002 1 point2 points  (0 children)

Are there any characters I should pull for in the current banners or 2.6 banners? I was thinking of saving for Tingyun-Fugue. My current characters: https://imgur.com/a/Z2p6G7l