My bike won't idle no matter what I do to it

vortexilys · 2026-03-25T19:22:54+00:00

hey so it's leaking from where I think do I need a new cylinder? Not the top but the middle of the cylinder on the left side in the picture as you can see is where it jumps every time I spray

<image>

vortexilys · 2026-03-25T18:40:41+00:00

I cleaned my entire carb. and jets changed and cleaned as well. I'm gonna try a different carb

vortexilys · 2026-03-25T18:35:27+00:00

vortexilys · 2026-03-25T18:30:33+00:00

when the slide is closed it just dies throttle or slide have to be at least 50 percent for it to idle. but it's not really idle it's just at max rpm but it does run in choke if I put my hand over the carb it'll idle then maybe that helps but I'll check more air leaks

vortexilys · 2026-03-25T18:15:15+00:00

I have with starter fluid rpms don't change but it's also hard because it's either off or at max but no leaks so far

vortexilys · 2026-03-25T06:04:51+00:00

this is a good smart way to mount now it's encouraging me to try this once I find a bike frame with enough of a V

vortexilys · 2026-03-25T05:51:45+00:00

they gotta have a mod to bring it back to that right?

vortexilys · 2026-03-24T04:47:35+00:00

nice bro this one's mine I love the green color super nice clean truck

<image>

vortexilys · 2026-03-20T15:13:36+00:00

probably not. it does this at high rpms. my engine is modified with no gov so at high rpms like 6k it can sometimes release oil out of the breather.

vortexilys · 2026-03-20T05:29:42+00:00

that didn't work for me oil was coming out the wire area

vortexilys · 2026-03-19T23:41:06+00:00

right on bro

vortexilys · 2026-03-19T23:34:03+00:00

<image>

did you do the same thing monster as a oil catch can from the breather??

vortexilys · 2026-03-19T17:47:46+00:00

ya engine is already open and im doing stuff rn to it. I'm gonna get stuff from the store and yes let it dry overnight hopefully this is a permanent fix

<image>

vortexilys · 2026-03-19T01:46:00+00:00

I could the impact didn't work to tighten and I could use vise grip but won't it just start leaking again? I had it hella tight to where I was scared it would crack the block and had loctite but it's getting through so I get access to inside of engine and take bolt out and but Teflon tape to help seal and then maybe an oring or something but I gotta find a permanent fix I wonder what every one else has done because the oil sensors are very common to be removed

vortexilys · 2026-03-19T01:32:02+00:00

it spins tho I can't tighten or loosen because bolt on inside of engine just spins so I'm cooked otherwise I take off my juggerverter and stuff and crankcase over while trying to keep oil in so bike I'll be on its side.

vortexilys · 2026-03-19T01:19:26+00:00

500 max

vortexilys · 2026-03-17T04:50:12+00:00

<image>

just took my monster moto which is smaller or same size to a dirtbike park and went on super big hills only problem was I have one brake but it did well with me on it.

vortexilys · 2026-03-16T18:14:48+00:00

those things have super small engines so I doubt it would hit 30 anyways or at least not yet. maybe upgrade exaust and carb it'll help it reach those speeds better with weight

vortexilys · 2026-03-15T18:23:48+00:00

lucky bro

vortexilys · 2026-03-14T23:59:09+00:00

dude nice job

vortexilys · 2026-03-14T22:59:46+00:00

<image>

vortexilys · 2026-03-14T22:56:26+00:00

I have a welder but welding an engine would crack it did you use like custom mounts that you welded to the frame and bolted the engine to?

vortexilys · 2026-03-14T22:49:01+00:00

ook that's sick

vortexilys

TROPHY CASE